| Document |
Document Title |
|
JPH0221249U |
|
|
JPH0220636U |
|
|
JPH0235168A |
PURPOSE: To make improvements in workability in site by laying a horizontal member, supporting a form of a column part of a target panel zone, over both upper and lower surfaces of a beam member, and attaching a steel plate doubling as t...
|
|
JPH022828Y2 |
|
|
JPH022944U |
|
|
JPH0161139B2 |
|
|
JPH0145301Y2 |
|
|
JPH0145299Y2 |
|
|
JPH0145300Y2 |
|
|
JPH0144690Y2 |
|
|
JPH0141799Y2 |
|
|
JPH0140902Y2 |
|
|
JPH01151555U |
|
|
JPH01150854U |
|
|
JPH0128192Y2 |
|
|
JPH0128190Y2 |
|
|
JPH0128189Y2 |
|
|
JPH0128191Y2 |
|
|
JPH0128188Y2 |
|
|
JPH0128195Y2 |
|
|
JPH0140192B2 |
|
|
JPH0126834Y2 |
|
|
JPH01182460A |
PURPOSE:To suppress the deformation of a beam mold frame supported without providing a support in a bottom part by suspending an end thick material of beam mold frame to a beam steel frame, provided extending in the lengthwise direction ...
|
|
JPH01178634A |
PURPOSE: To promote efficiency of construction works by placing concrete up to the lower part of a beam position in the inside of each of column forms at four corners, making arrangements in the insides of beam forms mutually combined on...
|
|
JPH01174727A |
PURPOSE: To secure the stable sealing effect by reducing the aperture diameter of the lower edge opened port of a skirt body installed at the lower edge part of a mould, in comparison with the aperture opened diameter of the upper edge o...
|
|
JPH01163362A |
PURPOSE: To improve strength by exposing the end section of a tie hoop buried in a PC split form from the end section of the form to form a U-shaped junction, butting the U-shaped junction against the junction of another split form to fo...
|
|
JPH0192450U |
|
|
JPH01146045A |
PURPOSE: To simplify and expedite field work and to improve erection strength by introducing precast concrete columns for cast-in-place erection as building columns, and using the precast concrete columns as cast-in-place concrete forms....
|
|
JPH01501407A |
A design by which tubular cardboard components are used to form moulds which have a constant non-circular cross-section. The walls of the tubular cardboard moulding component (11) are supported by an adjusting system of synthetic foam or...
|
|
JPS6444962U |
|
|
JPS6436864A |
PURPOSE: To improve workability through easy and rapid manufacture of stairs of commercial quality by providing a manufacturing device consisting of a base approximately in a T-shape in longitudinal section, a pair of outer forms integra...
|
|
JPS642003Y2 |
|
|
JPS646465A |
PURPOSE: To improve overall efficiency and to shorten the term of work by assembling a beam form and timbering for supporting it in advance at a place other than the site of installation and transporting the assembly and installing it on...
|
|
JPS63195055U |
|
|
JPS6358992B2 |
|
|
JPS6358993B2 |
|
|
JPS6343322Y2 |
|
|
JPS6343323Y2 |
|
|
JPS63171559U |
|
|
JPS6341472Y2 |
|
|
JPS6341473Y2 |
|
|
JPS63161940U |
|
|
JPS6339316Y2 |
|
|
JPS63152855U |
|
|
JPS63152857U |
|
|
JPS63152856U |
|
|
JPS6349028B2 |
|
|
JPS6334036Y2 |
|
|
JPS6343544B2 |
|
|
JPS63132045U |
|
