| Document |
Document Title |
|
JP3436231B2 |
To provide an installation structure for a blow molded article achieving low cost, favorable appearance, and sufficient installation strength. A lock member 3 is fixed to a bracket 2 embedded in a bottom wall 11 of a leg P1 of a spoiler ...
|
|
JP2003222111A |
To provide a driving type anchor which has strong resistance force against withdrawal from a prepared hole and prevents the head from making partial contact with a member.When forming a curved part 5 between the first straight line part ...
|
|
JP3418356B2 |
To allow coupling of plates as constituent members of a bed bottom part using the same coupling tool on the left and right of the bed and establish proper hitching even if the spacing of two or more screws to be hitched at the coupling t...
|
|
JP3419445B2 |
To provide a lid prevented from being lost and improving the safety of a worker by avoiding the sudden jump-out of the lid in detaching the lid to manually release a shift lock. This lid 11 for covering a through hole communicating from ...
|
|
JP3416627B2 |
To simplify a structure, improve fixing workability and efficiency, and secure the required fixing strength. When the rod-like section 6 of a fixed member 2 is inserted and fixed into a synthetic resin insert 3 having a tubular section 3...
|
|
JP2003156018A |
To reduce a curing time with joined strength between members being held even just after the joining and to correct displacement of a joining surfaces due to dimensional accuracy, when the members are inter-joined using a dowel.Diameter o...
|
|
JP2003148432A |
To fasten and fix a specified object by simply fitting a fastening cylinder and a fastening shaft to each other.According to this fastening method, the fastening shaft is pressed in the fastening cylinder, a locking piece projected on th...
|
|
JP3397790B2 |
Known anchor rails for construction engineering with at least one projecting anchor consist of a U- or C-shaped rail section to which is interlockingly linked a massive anchor bolt by upsetting or another deformation process. Deforming t...
|
|
JP2003090310A |
To prevent an article fitted to a wall or the like from being deviated or peeled.When a fitting shaft 12 of a connector 10 is inserted and fitted in a hole 100a of a tile 100, a projecting piece 12a is rubbed against an inner wall of the...
|
|
JP2003083312A |
To easily and inexpensively manufacture a constitutive member on the one hand, to easily install the constitutive member without a special tool on the other hand, and to allow the constitutive member to surely hold a measuring pipeline i...
|
|
JP2003074529A |
To provide an installing structure of an elastic stopper member capable of smoothly inserting a fixing portion into a hole without buckling a shaft portion of the elastic stopper member and suitably maintaining fitting of the fixing port...
|
|
JP2003074530A |
To provide a spacer capable of facilitating installing works and surely installing.An installing spacer 10 inserted in a dash silencer is provided with a hollow cylinder-shaped trunk portion 12, a first flange 13 extending from an one en...
|
|
JP2003506633A |
A fastener connects panel members in a flush position. The fastener includes a pair of connecting members which are snap-fit within apertures provided within each of the panel members for securing the panel members together. The fastener...
|
|
JP3375236B2 |
|
|
JP2003504569A |
A method for placing a functional element, especially a fastening element, in an especially liquid-tight and/or gastight manner, on a metal part. The inventive method is characterized in that a functional element provided with a hollow h...
|
|
JP2003027503A |
To provide a join structure between concrete structural bodies used to construct a three-dimensional structure in civil engineering works and capable of preventing a join part from deviating and dropping even when a strong external force...
|
|
JP2002352786A |
To improve heat radiating properties in a battery pack and increase the flexibility of position selection, when the battery pack is mounted in a motor vehicle. Connection parts 10d and 10e are provided on battery cells 10, and the connec...
|
|
JP2002308319A |
To ensure the sealing property even when the holding force is set at a degree wherein the attaching/detaching operability may not be spoiled.This hole closing lid member formed of an elastic material has a base section 10 and a resisting...
|
|
JP3334092B2 |
PCT No. PCT/EP92/02862 Sec. 371 Date Aug. 11, 1994 Sec. 102(e) Date Aug. 11, 1994 PCT Filed Dec. 10, 1992 PCT Pub. No. WO93/16292 PCT Pub. Date Aug. 19, 1993A self-drilling fastener includes a fastening element and a plate-shaped drillin...
|
|
JP2002295734A |
To provide an edge cover to improve mounting workability to a car body panel hole and improve a fixing force to a car body panel hole.The edge cover is provided with a cylindrical hole insertion part 4 having split structure, and panel l...
|
|
JP2002274515A |
To provide an attachment member which can realize firmer locking condition by a reception part and an insertion part, clearly obtain the click touch in the locking operation, visually confirm the locked condition from the outside, and ha...
|
|
JP2002250327A |
To provide a connecting metal used to fixedly connect adjacent columns to each other mainly in a prefabricated house, manufacturable at a low cost, being easily to carry and store.This connecting metal comprises a screw metal 13 having b...
|
|
JP3318324B2 |
The invention relates to a push-in plug (1) made from plastics and having at least one shank (2) to be introduced into a drilled hole, on which shank (2) there are located expansion segments (4) lying opposite one another in pairs, which...
|
|
JP2002213421A |
To provide a handle attaching structure for easily attaching a handle in a body armoring body.In this installing structure for attaching the handle 8 in a handle attaching part 7a of the body armoring body 1, a locking hole 9 and a throu...
|
|
JP3309005B2 |
PURPOSE: To efficiently perform a fixing operation by forming an inserting hole continuing to a hole in one sandwiching wall in a plate-like body after the plate-like body is sandwiched between a pair of sandwiching walls of fixing membe...
|
|
JP2002205479A |
To provide a mechanism for easily fitting and removing a binder 2 as well as a file using the mechanism.A groove 39 for a driver is provided in the head part 31 of a rivet 3, and a threaded groove 34 is provided in a thread part 32, wher...
|
|
JP2002521637A |
The control device has a control circuit and a pressure sensor for measuring the hydraulic pressure in the gearbox. The control circuit and the pressure sensor are accommodated in a common housing. The housing has a metallic baseplate wh...
|
|
JP2002520561A |
A sealing disk which is provided with a contour with which a contour or a face of a component on which the disk is to be disposed, is associated in complementary fashion. For premounting of the disk fixed on the component, the disk has a...
|
|
JP2002181017A |
To widen a selection range of an anchor bolt of a mounting object to correspond to various anchoring forms and to facilitate construction management.A sleeve 11 having a plurality of expansion pieces 13 on a tip side is fitted into a nut...
|
|
JP3295163B2 |
PURPOSE: To provide hot-plug retaining structure for a diesel engine, capable of preventing the falling of a hot plug by simple structure, without requiring a high pressure proof seal between a hot plug and a cylinder head, and also with...
|
|
JP2002174218A |
To easily receive a receiving plate portion of an inserting portion provided on an attaching object between a pair of clipping plates composing a clip, and to securely ensure a fit-in state.This coupling structure comprises the clip 2 pr...
|
|
JP2002161699A |
To provide a joint structure of structural bodies capable of saving energy for construction work of the structural bodies by easily connecting the structural bodies to each other.The joint structure of the structural bodies is constitute...
|
|
JP2002070892A |
To provide a magnetic clutch, in which a laminating body is a constructive element, capable of reducing effectively a collision noise generating at the moment when an armature plate and a driving rotor are combined together and also capa...
|
|
JP2002506955A |
A connecting means adapted to releasably fix or release a first element ( 4 ) and a second element ( 5 ) includes a locking pin ( 1 ) which is moveable by remote activation means between a locked position, in which leg ( 8 ) expands wall...
|
|
JP2002039129A |
To provide a grooved pin having a simple configuration and a secure tightening holding force and inexpensive.This grooved pin 1 is guided by a groove formed in parallel with an axial line and is pressed in along an inner face of a pressi...
|
|
JP2002503557A |
A method for mounting a bushing into a metal member which comprises providing a metal member forming a bushing receiving opening in the metal member, the opening defined by an annular edge portion surrounding the opening. A bushing is th...
|
|
JP2002021869A |
To provide a low cost grooved pin of a simple construction and an accurate alignment property.This pin has plural strip grooves 10 comprised of top parts 11 and valley parts 12 formed, and a diameter of a locus circle connecting ridge li...
|
|
JP3234116B2 |
PURPOSE: To provide a joint structure between honeycomb panels excellent in rigidity and strength, simple and easy in execution work, rich in general purpose usability and excellent in a cost respect. CONSTITUTION: In a joint structure, ...
|
|
JP2001322507A |
To provide a mounting structure for an EA material capable of mounting the EA material to a member for trimming or the like without causing backlash and without using a hot melt adhesive.A rod 2 is projectively provided from the trimming...
|
|
JP2001317514A |
To provide an easily-driven and hardly-removable dowel pin driven into a hole bored in a joint face between two wooden materials to be connected for connecting them together.In the dowel pin 1 provided with stopping claws 3 arranged in t...
|
|
JP2001521090A |
An element for securing railway rails on a solid track comprises an anchor (16) with a cone (6) in its front region followed by a mixing centring head (7), and a bolt (16) whose surface is partially provided with a profile (5). This anch...
|
|
JP2001277985A |
To provide an air bag excellent in an external appearance in a cabin. This clip device is composed of a connecting pin 50 installed on the reverse of a cover member 20, and the connecting pin 50 comprises a head part 52 connected to the ...
|
|
JP3212671B2 |
PURPOSE: To connect two profile members dismountably. CONSTITUTION: An insert core 2 is inserted and fixed in a profile member 1. The core 2 has an axially movable bolt 7. The distal end of the bolt 7 supports in a pivoted manner retaini...
|
|
JP2001234912A |
To provide a stone and a stone mooring metal fitting friendly to the environment and rigidly fixable to the stone.A pair of mounting holes 5 is formed with a mutual distance on the stone 3 and they are obliquely provided so that the dist...
|
|
JP2001513027A |
Metal members are joined to each other by the use of depending collars and through holes. A tool head inserted through the collars and holes and the tool shoulder exert pressure to simultaneously bend and crimp the collar. This technique...
|
|
JP2001511239A |
The invention relates to a shaft and hub connection for securing bearings, in particular ball bearings (12), on a shaft (10). The proposal is made that the hub part (14) of the bearing (12) encompassing the shaft (10) have at least one a...
|
|
JP2001200818A |
To provide a clip for installing a part such as a trim board of a car on a panel such as a door panel capable of installing the part by inserting the clips into the mounting holes of the part. A mounting hole 220 of a part (for example, ...
|
|
JP2001146911A |
To position correctly without a waste of a time and a material. A device and a method for positioning a first piece 4 to a predetermined position in relation to a second piece 6 are disclosed. This device 2 has a tab 8 and a slot 10. The...
|
|
JP2001120445A |
To provide a kitchen knife stand capable of preventing screws from dropping or projecting to the surface of a door. A main body 3 for hanging kitchen knives 15 inserted into insertion holes 7 of this kitchen knife stand 1 is attached to ...
|
|
JP2001107930A |
To provide a brake force control device capable of performing displacement by the amount of a pad clearance in a shorter time at an initial stage of starting braking of a brake unit. A pressure chamber 7a of a brake unit 7 is furnished w...
|
