| Document |
Document Title |
|
JPS6131765B2 |
|
|
JPS61115814U |
|
|
JPS6131762B2 |
PURPOSE:To minimize formation and accumulaion of tar-like substance at vaporizing section for improvement of combustion performance by employing a porous body composed of a special (or a particular) fibrous material. CONSTITUTION:A porou...
|
|
JPS6131364B2 |
|
|
JPS61159013A |
PURPOSE: To keep a good red-heat state with a wide range of adjusting combustion amount and a wide radiation area by installing a secondary flame ring and a flame hold ring in such a way that a flame adjusting part is formed above second...
|
|
JPS61159012A |
PURPOSE: To reduce an offensive odor at the usual time of fire-cut by installing at least one auxiliary wick part in the main wick in such a way that the height of the auxiliary wick part is higher than the other parts of the main wick a...
|
|
JPS61159018A |
PURPOSE: To enlarge the adjusting range of combustion by installing a fuel path which controls the heat input to a wick simply and largely by adjusting the flow rate and is made as one body with wick guide cylinder or contacting closely ...
|
|
JPS61159019A |
PURPOSE: To enlarge the adjusting range of combustion and improve start up condition after ignition by installing a pipe for raising up bubbles between a heat absorbing pipe and a radiator in such a way that the pipe for bubbles is insta...
|
|
JPS61159016A |
PURPOSE: To improve purifying efficiency and durability by installing a catalyst layer at the upper end opening portion of a combustion cylinder and a screening plate which has many ventilation holes at a specified distance lower from th...
|
|
JPS61159014A |
PURPOSE: To be able to enlarge the range of adjusting combustion amount and increase in radiation heat at a red-heat zone by forming ventilation holes, a flame adjusting part and a flame holding part in such a manner that the holes are b...
|
|
JPS61110919U |
|
|
JPS61110917U |
|
|
JPS61110916U |
|
|
JPS61110915U |
|
|
JPS61153401A |
PURPOSE: To reduce an odor at the time of extinction without making larger the main body by installing a fuel condenser at the first half place and a suck-in device at the second half of the exhaust port of a fixed tank. CONSTITUTION: At...
|
|
JPS61153403A |
PURPOSE: To simplify the constitution and bring the function into good play by installing a heat absorbing element of controller for wick temperature in such a way that the element is wrapped and fixed by the edge of a burner plate place...
|
|
JPS61149736A |
PURPOSE: To contrive to make the resin coating film generate the phenomenon for absorbing the radiating heat from a red-hot outer flame cylinder and radiating above absorbed radiating heat, then make the outer periphery surface of a glas...
|
|
JPS61106713U |
|
|
JPS61106710U |
|
|
JPS61106714U |
|
|
JPS61106712U |
|
|
JPS61106763U |
|
|
JPS61106711U |
|
|
JPS6121688Y2 |
|
|
JPS61140710A |
PURPOSE: To be able to hold a glass cylinder with a high accuracy simply and cheaply by installing a metal fitting which is elongated downwards and of which end is connected to one of the inner and outer combustion cylinders and a part o...
|
|
JPS61140708A |
PURPOSE: To provide a combustion cylinder without imperfect combustion etc. by installing a bottom ring at the end of the outer combustion cylinder in such a way that the dia. size at the bottom end of the ring is suitable to be placed o...
|
|
JPS61140709A |
PURPOSE: To improve purifying performance for exhaust gas with no disturbance of combustion by coating the walls of inner, outer combustion cylinders and ceiling inside with the films which have a specific thickness and are composed of c...
|
|
JPS6127647B2 |
|
|
JPS6127646B2 |
A liquid fuel combustion apparatus comprises a combustion cylinder for supporting a wick to be vertically movable between a combustion position and an extinguished position, a rotating shaft connected to said wick for raising and lowerin...
|
|
JPS61138011A |
PURPOSE: To improve a heating effect, as well as contrive to produce a thin type burning equipment by a method wherein a rear side surface body of an outer cylinder faced to the secondary red heated body is constituted with a heat-reflec...
|
|
JPS61138012A |
PURPOSE: To obtain a burning equipment capable of maintaining a stable burning condition by a method wherein in a perforated plate which is formed a combustion chamber, at its surrounding area near by around the tip-end of a wick, a pitc...
|
|
JPS61134512A |
PURPOSE: To make a high efficiency of radiation, and enable both this efficiency of radiation and a characteristic of discharged gas to be applied in response to a variation in burning amount by a method wherein a flat primary combustion...
|
|
JPS61134513A |
PURPOSE: To enable a substantial increase of thermal radiation volume with a simple construction by a method wherein a flat combustion chamber formed with a porous plate acting as a red heater and an outer cylinder having a window member...
|
|
JPS61134511A |
PURPOSE: To reduce a strain of porous plate during combustion and enable a stable and uniform combustion state to be kept by a method wherein one end of a spacer is fixed to one of the inner surfaces of the porous plate which are opposed...
|
|
JPS6196119U |
|
|
JPS6196120U |
|
|
JPS61130714A |
PURPOSE: To permit odorless of fuel vapor caused by a suction device by a method wherein absorbent which absorbs the fuel vapor in addition to the suction device is provided on the exhaust port of the suction device and the absorbent is ...
|
|
JPS6125962B2 |
|
|
JPS61128034A |
PURPOSE: To make a low total height of a casing and keep a stable feature of a kerosene burner against fall by a method wherein the upper part of a flue cooperatively connected to the upper part of the combustion chamber is bent to open ...
|
|
JPS61128015A |
PURPOSE: To enable a keeping of stable and complete ignited condition to be performed by a method wherein a red heated part arranged at an intermediate upper part of a combustion chamber is made as an L-shape structure having flanges and...
|
|
JPS61128014A |
PURPOSE: To enable a large amount of radiation heat to be provided by a method wherein a red heated part of porous plates constituting a flat combustion chamber which faces against a window is constituted by a separate member which is se...
|
|
JPS61128035A |
PURPOSE: To enable an amount of a secondary radiation heat from a window to be increased by a method wherein upper and lower continuous concave and convex parts are arranged in parallel at least an inner surface of the window member faci...
|
|
JPS61125510A |
PURPOSE: To stabilize the lowered position of a wick for the purpose of extinguishing the flame of the wick and to prevent oil from leaking from the heater when it is upset by providing a step section of an expanded pipe beneath a wick g...
|
|
JPS6119295Y2 |
|
|
JPS6119284Y2 |
|
|
JPS6119294Y2 |
|
|
JPS6119286Y2 |
|
|
JPS6119287Y2 |
|
|
JPS6119340Y2 |
|
|
JPS6119285Y2 |
|
