| Document |
Document Title |
|
JP2968874 |
PURPOSE: To automatically measure calorific value of coal and the like at regulated accuracy by setting a combustible capsule, in which powder of coal and the like is sealed by a predetermined amount, to the lower surface of the lid of a...
|
|
JP11201923 |
To obtain a measuring method in which specific heat in a high-temperature region can be measured with high accuracy in the small number of measuring operations even when a temperature around a sample is not uniform. A heat flux-type diff...
|
|
JP2959895 |
PURPOSE: To obtain a basic value for heating or cooling a substance by placing at least two temperature-measuring elements which are located at different distances from an electrical heating element within a substance, allowing the heati...
|
|
JP2958866 |
To provide the detecting method and detector of an enthalpy difference which occurs at the time of cooling a gas flow containing water vapors down to a temperature under a dew-point temperature. In this method which is used e.g. for dete...
|
|
JP2954483 |
PURPOSE: To reduce cost and easily replace a temperature sensor by performing temperature compensation operation based on storage data when dispersious are found in forward voltage offset and temperature coefficient of the temperature se...
|
|
JP2949314 |
PURPOSE: To provide a calorimetric unit and method whereby the heat capacity of trace amounts of samples can be measured with high accuracy. CONSTITUTION: In the sample container 1 and the heat insulated container 7 of an insulated calor...
|
|
JP11174010 |
To measure quantity of heat more accurately even if the prssure of a gas to be measured is varied. In a heat quantity calculation part 112, the heating value H of a gas to be measured is calculated from a heat conductivity λ m calculate...
|
|
JP11160493 |
To provide a wet calorific value measuring device capable of lessening measuring items, simplifying structure and highly precisely measuring. A whole vitrificated body put in a canister 2 is submerged in a measuring tank 11 supplying wat...
|
|
JP11142261 |
To prevent damages, breaks to a sensor and eliminate maintenance by indirectly sensing snowing and frosting from changes of a heat flow density and a temperature. A heater ground 21 is formed on a road face ground 25, and a sensor part 2...
|
|
JP2933761 |
PURPOSE: To automatically opening/closing a lid of a pressure container, and to measure calorific value accurately and promptly by forming the lid into bayonet shape having a protruded part on the upper surface, and by providing a lid su...
|
|
JP11142260 |
To provide a new heating value measuring instrument which can accurately find the total heating value of a glass solidified body by greatly reducing its heat flux measurement error. This instrument includes a flank heat flux measurement ...
|
|
JP11108773 |
To highly accurately control rolling finish temperature by calculating the plate thickness average temperature of a metal plate from the surface temperature of the metal plate heated to a specified temperature, a plate thickness and a de...
|
|
JP11094654 |
To simply and inexpensively grasp calorific value of a fuel gas before preparing a gas miture, and to set the air-fuel ratio to a prescribed value before combustion, by inserting a light emitting material into the flame of fuel gas and b...
|
|
JP11094655 |
To make performable desired accurate calorimetry by effectively avoiding the incorrectness of calorimetry due to the difference in external temperature between a sample for calorimetry and a reference sample. This device has a calorimetr...
|
|
JP11083772 |
To quantize a proliterating step of microorganism by an optical reaction and optical anti-bacterial properties of an optical anti-bacterial material, by introducing a light to a fixed temperature conduction type calorimeter, and measurin...
|
|
JP2898196 |
PURPOSE: To facilitate the manufacture and fabrication and to make the length of a sealing wire a short constant length regardless of the thickness of the pipe of heat medium. CONSTITUTION: A temperature-sensing part 2 and a protecting p...
|
|
JP11063968 |
To obtain a method for measuring an air gap by a thermal flux detection of casting mold, and a thermal flux detector and a sensor in the same device. A lubricous layer by a lubricant 57 is formed between a mold wall face W of casting mol...
|
|
JP11064120 |
To simplify the structure, reduce the cost and improve the durability by fixing a side cylinder to the side surface of a heat receiving plate so as to cover a heat insulating groove and neatly arrange the front end, and inserting sheath ...
|
|
JP11030599 |
To provide a heat accumulation quantity measuring method that can easily know the heat accumulation quantity in a lower-dimensional evaporator and two-dimensional cooling facilities that use carbon dioxide as a cooling medium in a lower-...
|
|
JP2873367 |
To provide a device for measuring the characteristics of heat and moisture transfer capable of accurately measuring the characteristics of the heat and the moisture transfer of a clothing material at the same time and obtaining basic dat...
|
|
JP11004023 |
To decrease the resistance of a leg part and to suppress the voltage drop on the leg part while heat conductance, which is same as the case where titanium is used, is being maintained using titanium silicide as the wiring material of the...
|
|
JP10332683 |
To provide a method for measuring the ventilation heat radiating property of a sample of a knitted fabric, woven fabric, etc., used for clothes when mankind moves by using a device having a dummy perspiration mechanism which simulates a ...
|
|
JP10318855 |
To provide a calorific value measurement device wherein a measurement time is shortened and measurement precision is improved. A measurement stage 2 wherein a plurality of glass solidified bodies 1 are placed while they are circumferenti...
|
|
JP10281863 |
To obtain a device for detecting an optical parameter that detects the deviation of the center of the average power or the intensity distribution of a laser beam and can monitor a diameter or the intensity distribution of a beam itself t...
|
|
JP10274563 |
To easily and accurately measure the radiation rate of a radioactive waste body with a long service life. A radiation rate measuring device for a radioactive waste body is provided with a reflecting side iron piece 28 with the mirror sur...
|
|
JP10267763 |
To easily and accurately measure the heating value of radioactive waste. This measuring device includes a measuring container 22 which has a closing lid 20 so that it can be opened and closed and which is formed of a thick steel plate 21...
|
|
JP2829248 |
PURPOSE: To obtain a sample bag for measuring the quantity of heat which enables accurate measuring of the quantity of heat of a sample having high volatility, and a measuring method of the quantity of heat using the same. CONSTITUTION: ...
|
|
JP10227703 |
To provide a small heat flux meter with good durability. This heat flux meter includes a heat-receiving-surface tube 2 in the form of a cylinder closed at an end face and being smaller in diameter than the end face, an outer frame pipe 3...
|
|
JP10206243 |
To measure in a short time the amount of heat generated inside an object without waiting for a stationary state, by obtaining the amount of heat generated inside the object and a temperature distribution through a back calculation and an...
|
|
JP10206360 |
To save energy (reduce a cost) by shortening the time necessary to inspect a temperature of a vacuum heat insulating structure body, and raising an inside temperature of the vacuum heat insulating structure body in a short time as well a...
|
|
JP2799290 |
PURPOSE: To make a device in a pocket size by detecting the temperature change of thermal raw material receiving laser energy by a temperature sensor, generating a differentiating signal by a differentiator, and transferring the signal t...
|
|
JP10170459 |
To improve the measurement accuracy of specific heat capacity by arranging hemispherical mirrors at both sides of a sample at opposing locations, increasing the effective absorptivity and effective emissivity of a sample surface close to...
|
|
JP10170354 |
To make it possible to enhance operating efficiency by a method wherein a nozzle plate is turned, a nozzle hole is made to agree with a communication hole between both flanges, a vapor is spouted from the nozzle hole, a vapor pressure be...
|
|
JP10153496 |
To precisely grasp the heat value of a glass-solidified body by measuring the temperatures of a heat value measuring medium carried from a measuring vessel to a medium circulating means and the heat value measuring medium carried from th...
|
|
JP10132767 |
To measure a boiling point simply and with good accuracy by sealing up a cell, in which a sample is put and a lid via a hard wire, and forming a small hole with it. As the size of an airtight cell, the area of its bottom part is normally...
|
|
JP10135523 |
To improve diffusion prevention performance in a contact part between an element and a junction board by constituting a diffusion prevention structure of a thermoelectric device having n-type and p-type conductor elements and a junction ...
|
|
JP10123075 |
To eliminate a need of the blackening treatment on the surface of a sample in a thermal-diffusivity measuring method, by a laser flash system, in which the sample whose absorptance and emissivity regarding a thermal radiation are low is ...
|
|
JP10122984 |
To continuously and precisely grasp the heat possessed by a fused slag without reforming an equipment by measuring the flying distance from a gutter outlet when the fused slag to be supplied to a blowing device is freely fallen from the ...
|
|
JP10115563 |
To provide an electrolytic cell which regulates a temperature so as to be operated at the boiling point of an electrolytic solution or at a temperature near the boiling point and which collects the electrolytic solution. An electrolytic ...
|
|
JP2775208 |
PURPOSE: To measure the heat conductivity or the heat conductivity change or the both being fine in replaceability of a gas to be measured in the vicinity of heat conductivity detector while the heat conductivity detector receives no inf...
|
|
JP10068660 |
To provide the detecting method and detector of an enthalpy difference which occurs at the time of cooling a gas flow containing water vapors down to a temperature under a dew-point temperature. In this method which is used e.g. for dete...
|
|
JP2756205 |
PURPOSE: To obtain a calorific value measuring apparatus which can easily clean a gas cylinder and continuously supply current to an electrode and also which can simplify a structure of a lid for a calorific value measuring tank. CONSTIT...
|
|
JP10038827 |
To detect miscellaneous gas in a short time using a heat conductivity tape calorimeter that can measure the calorific value of stock gas at high speed. A heat conductivity type calorimeter 6 for measuring heat conductivity at the specifi...
|
|
JP10038826 |
To reduce a calorific value measuring error caused by the change of composition due to intermixture of impurities or the like in the case of measuring the calorific value of mixed gas using a heat conductivity type calorific value meter....
|
|
JP2744172 |
PURPOSE: To increase the number of durable times of a heater and reduce the replacement frequency and at the same time automatically and continuously measure a calorifit value by transferring the heat which is generated by the heater to ...
|
|
JP10026594 |
To obtain a thermal analysis element for satisfactorily thermally analyzing a trace amount of sample. A frame-like board 2 having a predetermined thickness is covered with a thin film 3, and sample cells 4A, 4B for containing and holding...
|
|
JP10018172 |
To provide a device for measuring the characteristics of heat and moisture transfer capable of accurately measuring the characteristics of the heat and the moisture transfer of a clothing material at the same time and obtaining basic dat...
|
|
JP2734491 |
PURPOSE: To improve accuracy of two-phase flow enthalpy measurement. CONSTITUTION: The two-phase flow enthalpy measuring apparatus comprises a base pipe 1 where two-phase flow flows, a suction pipe 2 inserted into the base pipe and havin...
|
|
JP09318665 |
To provide an energy and resource consumption control system capable of visually informing energy, resource flow and consumption states so as to improve consciousness toward resource conservation and promote proper action and being put i...
|
|
JP09318464 |
To provide a heating amount-measurement device which, relating to a heating device which uses both infrared ray heating and hot air heating, can measure respective heating amount separately. A heating amount measurement device comprises ...
|
