| Document |
Document Title |
|
JPS5757975B2 |
|
|
JPS5756031B2 |
|
|
JPS57191583A |
PURPOSE: To shorten a manufacture time by bonding and fixing a middle and a pipe together with an adhesive which sets by ultraviolet-ray irradiation. CONSTITUTION: After a metallic pipe 2 is implanted in a metallic middle 1, a pipe neck ...
|
|
JPS57191582A |
PURPOSE: To achieve work in a short time while eliminating defection in quality by heating and brazing parts to be brazed instantaneously by a resistance welder. CONSTITUTION: A foil-like brazing material 13 is used and cut to nearly the...
|
|
JPS57185990U |
|
|
JPS57187684A |
PURPOSE: To secure a stable operation of oscillation not depending on supply voltage and to lower power consumption by using a low-current bias method. CONSTITUTION: A time reference signal which is an output of a quartz oscillator 520 i...
|
|
JPS5752550B2 |
|
|
JPS5752551B2 |
|
|
JPS5752546B2 |
|
|
JPS5751636B2 |
|
|
JPS5749829Y2 |
|
|
JPS57173062U |
|
|
JPS5751075B2 |
|
|
JPS5749195Y2 |
|
|
JPS57168088U |
|
|
JPS57171280A |
PURPOSE: To make it possible to remarkably shortening the manufacturing process while stabilizing and thinning the back cover and minimizing the production of unacceptable products, by producing the back cover through a continuous cuttin...
|
|
JPS57164489U |
|
|
JPS57166586A |
PURPOSE: To shorten a pace measurement time and to prevent an increase in current consumption by outputting pulses for pace measurement for a certain period after resetting is released. CONSTITUTION: After a clocking circuit 2 is release...
|
|
JPS5747431B2 |
|
|
JPS5747436B2 |
|
|
JPS5745587Y2 |
|
|
JPS57156886U |
|
|
JPS57156887U |
|
|
JPS5746076B2 |
|
|
JPS5744215Y2 |
|
|
JPS5744953B2 |
|
|
JPS5743270Y2 |
|
|
JPS5743876B2 |
|
|
JPS5741704B2 |
|
|
JPS5739831Y2 |
|
|
JPS57141580A |
PURPOSE: To realize a quick control of time rate with the trimmer adjustment of a short time, by delivering the inphase motor driving output of a prescribed cycle in the reset mode and then delivering the logic brake pulse in a prescribe...
|
|
JPS5739396B2 |
|
|
JPS57132278U |
|
|
JPS57132277U |
|
|
JPS57125375A |
Method of fixing the outside end (2) of a hairspring to a peg (3). The peg (3) has a flat surface (8) arranged orthogonally to an imaginary plane tangential to the end (2) of the hairspring at the point of contact. This flat surface may ...
|
|
JPS57125376A |
PURPOSE: To enable a terminal to set 3 conditions of a watch by a simple mechanism, by controlling opening and closing of a gate and resetting of a counter in accordance with 3-value signal including floating level. CONSTITUTION: When a ...
|
|
JPS57122575U |
|
|
JPS57121665U |
|
|
JPS57113387A |
PURPOSE: To make a reference oscillator unnecessary by a method wherein crystal is used as a filter in order to detect the phase difference between the output and input of the crystal filter and to measure frequency slippage. CONSTITUTIO...
|
|
JPS57108787A |
PURPOSE: To realize the simple and quick diagnosis for a fault of a driving part or a step motor, by carrying out the diagnosis based on the fault of a current waveform of the drive signal supplied from the step motor. CONSTITUTION: The ...
|
|
JPS57108688A |
PURPOSE: To improve the designing freedom by laser welding of a glass rim with the body made as separate parts from a designing standpoint in the watch casting. CONSTITUTION: In the casting of a non-waterproof watch, a laser beam 12 is i...
|
|
JPS5731116B2 |
|
|
JPS5729308Y2 |
|
|
JPS5794888U |
|
|
JPS5791232A |
|
|
JPS5786777A |
PURPOSE: To insert pulse signal of step information and shorten the time required for measuring steps by stopping ordinary driving pulses of an electronic watch during step measurement and after finishing the step measurement advanc ing ...
|
|
JPS5786061A |
PURPOSE: To warm up the operation of an oscillator and perform measurement in a short time by applying voltage to circuit blocks from power source terminals operating cooperatively with a conveyor prior to measurement. CONSTITUTION: Shor...
|
|
JPS5786490U |
All the movable members (12 to 16) are actuated by cam discs (7 to 11) which detect rotational movements of ellipse (24), spiral spring (21) and degree-of-angle pulse transmitter (28) by optoelectronic sensors (25 to 27). Program sequenc...
|
|
JPS5779484A |
PURPOSE: To achieve measurement due to a general frequency measuring instrument by selectively outputting frequency measurement signals of respective oscillation circuits in an electronic timepiece circuit block incorporating plural osci...
|
|
JPS5770186U |
|
