| Document |
Document Title |
|
JPS63167662A |
PURPOSE: To reduce the cost of a laminated type electromagnetic pump for fluid by laminating the actuators of the pump in an electromagnetic pump to eliminate extremely low voltage and large current, thereby preventing the diameter of a ...
|
|
JPS63166104A |
|
|
JPS63157661A |
PURPOSE: To make a pump compact and to make it to work at highest effi ciency, by providing multiple intermediate ducts where armatures are built in between inside and outside ducts, and by forming multiple channels. CONSTITUTION: Inside...
|
|
JPS63157662A |
PURPOSE: To resume the smooth supply of molten metal at the time when the operation of an electromagnetic pump is restarted, etc., by stably keeping the molten metal in continuous condition in the duct during the time the operation of th...
|
|
JPS63145990A |
|
|
JPS6388799U |
|
|
JPS63136952A |
PURPOSE: To allow conductive fluid such as sea water, etc., to be sent out without using an impeller or a motor, by forming the magnetic field in the direction of a right angle to the flow of conductive fluid with superconductive magnet ...
|
|
JPS6327670B2 |
|
|
JPS63125858A |
PURPOSE: To improve the reliability by interposing a magnetic fluid type actuator between both elbows of one opposite angle of a diamond-shaped lever, and mounting compression springs among both elbows of the other opposite angle and the...
|
|
JPS63125857A |
PURPOSE: To easily adjust the driving stroke with high accuracy by forming a diamond-shaped lever by four levers, interposing a magnetic fluid type actuator between both elbows of one opposite angle of the diamond-shaped lever, and conne...
|
|
JPS6322907B2 |
|
|
JPS63101795A |
|
|
JPS6389050A |
PURPOSE: To eliminate the possibility of the damage of an outer wall by a liquid at a high temperature by passing mercury vapor at a high temperature obtained by heating liquid mercury into magnetic flux. CONSTITUTION: A center shaft 12 ...
|
|
JPS6380759A |
PURPOSE: To improve the efficiency of an electromagnetic induction prime mover by composing to act a magnetic field and a current to an annularly sealed fluid. CONSTITUTION: A passage 1 is annularly formed, and mercury 2 is circulated as...
|
|
JPS6373868A |
PURPOSE: To prevent cooling and solidification of a molten metal by making a conduit of a conductive refractory material and providing an induction heating means of said conduit. CONSTITUTION: In a molten-metal feeder using an electromag...
|
|
JPS6373006A |
|
|
JPS6310661B2 |
|
|
JPS637989U |
|
|
JPS632089B2 |
|
|
JPS631021B2 |
|
|
JPS633293A |
|
|
JPS62191378U |
|
|
JPS6245512Y2 |
|
|
JPS62188981U |
|
|
JPS6256750B2 |
|
|
JPS62272860A |
PURPOSE: To enable power generation at a low temperature by a method wherein ionization raw material being liable to be ionized is used as a working fluid. CONSTITUTION: A working fluid 9a in liquid as ionization raw material being liabl...
|
|
JPS62185486U |
|
|
JPS6255946B2 |
|
|
JPS62268354A |
PURPOSE: To increase flow rate at electromagnetic pump side and to improve the pump efficiency and to eliminate influence of thermal stress strain, by a method wherein a duct section of generating side is as wide as a half of that of ele...
|
|
JPS62261997A |
|
|
JPS62262652A |
PURPOSE: To compensate the braking effect due to the current bypass on a generator side and the leakage magnetic field on a pump side, by performing the connecting pipework on both sides of a coupler with an electrically good conductor a...
|
|
JPS6251071B2 |
|
|
JPS6241592Y2 |
|
|
JPS62230350A |
PURPOSE: To convert the thermal energy of a high pressure gas efficiently into electrical energy by periodically shrinking an annulus ring formed by a liquid metal in the radial direction by gas pressure and working a magnetic field in t...
|
|
JPS62502652A |
|
|
JPS62217853A |
PURPOSE: To increase pump capacity easily to a high one by forming an annular flow path of liquid metal wound with a coil along the axial direction by coaxially providing a plurality of flow paths differing in the annular diameter. CONST...
|
|
JPS6243430B2 |
|
|
JPS62207170A |
PURPOSE: To prevent damage to a thermal shock, etc. by using a metallic pipe as the main body of a duct and executing a ceramic layer onto the inner circumferential surface of the metallic pipe. CONSTITUTION: An induction coil 3 is mount...
|
|
JPS6242704B2 |
|
|
JPS62190517A |
|
|
JPS62189969A |
PURPOSE: To minimize the ohmic loss of the fluid in the total loss in the circular passage and to obtain a proper characteristic of the quantity of flow - discharge pressure. CONSTITUTION: Between double pipes 11 and 12 a circular passag...
|
|
JPS62129286U |
|
|
JPS62181665A |
PURPOSE: To simplify repair by composing an inductor for an electromagnetic trough of a plurality of units, separately constituting each unit through concentrated winding to a core with salient poles in the multiple of three and executin...
|
|
JPS62502023A |
|
|
JPS62123353U |
|
|
JPS62178153A |
PURPOSE: To improve efficiency, by forming the insulation of a coil with inorganic material, and by filling up a frame with inert gas. CONSTITUTION: An electromagnetic pump is organized by forming a duct 2 for a passage for circulating s...
|
|
JPS62163558A |
PURPOSE: To generate the power from the heat energy without noise emission by making the electroconductive heat medium vapour cross the transverse magnetic field. CONSTITUTION: A heat pipe type generator is composed of a sealed hollow ve...
|
|
JPS62160991A |
PURPOSE:To obtain a water feed force for a ship's propulsion by exciting an exciting coil on a ship's hull and supplying an alternate electric current of the same phase angle as generated magnetic flux to electric poles arranged at the o...
|
|
JPS62160066A |
PURPOSE: To simplify the structure and to enhance the efficiency of an annular magnetic field type electromagnetic fluid apparatus by forming a closed loop-like magnetic field in a conductive fluid, and employing the closed magnetic fiel...
|
|
JPS6230861B2 |
|
