| Document |
Document Title |
|
JPH0429315U |
|
|
JPH0429314U |
|
|
JPH0423222U |
|
|
JPH0423221U |
|
|
JPH0453621A |
PURPOSE: To prolong the service life of a band saw blade as well as to check its vibration to the utmost by installing an opposed saw blade insert, guiding and supporting a side face of the band saw blade, in a saw blade housing freely a...
|
|
JPH048164B2 |
|
|
JPH0413220U |
|
|
JPH0413219U |
|
|
JPH0413218U |
|
|
JPH0425316A |
PURPOSE: To enable an attaching operation following a recovering operation of a band saw blade by enabling the reversal of a saw blade changer only on a return path in turning a turning arm. CONSTITUTION: In a band sawing machine in whic...
|
|
JPH0425315A |
PURPOSE: To enable automatic change of band saw blade by turning upper and lower saw blade carriers, expanding and overlapping them, transferring a band saw blade trained over a saw blade attaching magazine to drive and driven wheels and...
|
|
JPH0425317A |
PURPOSE: To cut and widen again a cut section of a workpiece narrowed along with the ascent of a band saw blade with the band saw blade for reducing a press force between the section of the workpiece and the side of the band saw blade by...
|
|
JPH0425314A |
PURPOSE: To enable automatic change of a band saw blade by parallelly moving a saw blade magazine provided in a magazine holder to insert removably the saw blade magazine in a drive wheel and driven wheel. CONSTITUTION: When a band saw b...
|
|
JPH049218U |
|
|
JPH049219U |
|
|
JPH0419009A |
PURPOSE: To provide automatic replaceability for band saw element by furnishing a saw element replacing device which can be revolved by a revolving arm, changing the part of a saw element magazine with revolution of the revolving arm, an...
|
|
JPH042518U |
|
|
JPH03294115A |
PURPOSE: To carry out efficient cutting by providing a cylinder for raising head for supporting full dead weight on the head side between a machine table and a head and providing an automatic throttle valve device for adjusting a dischar...
|
|
JPH03126518U |
|
|
JPH03126516U |
|
|
JPH03126519U |
|
|
JPH03126520U |
|
|
JPH03256610A |
PURPOSE: To simplify the installation of a band saw in a saw edge housing by providing at least one of a pair of barrel and back guiding members between a guiding position and a guide escaping position in a movable fashion. CONSTITUTION:...
|
|
JPH03109720U |
|
|
JPH03228516A |
PURPOSE: To automatically replace band saw blades by providing a swing member incorporating a pair of wheels in a band saw blade housing for a band saw blade, and by arranging the swing member adjacent to a pair of wheels on which an unu...
|
|
JPH0396160U |
|
|
JPH03221355A |
PURPOSE: To estimate the life of a sawtooth edge by automatically determining the consumption rate of the sawtooth edge when a work piece is cut or the cross section area of the work piece to be cut next which can be cut before the end o...
|
|
JPH0393026U |
|
|
JPH0393025U |
|
|
JPH03208519A |
PURPOSE: To facilitale handling and maintenance to improve operating efficiency by inputting the size of a work from an input unit, corresponding to this, and by computing the interval of a saw blade guide to be set automatically. CONSTI...
|
|
JPH03202221A |
PURPOSE: To installing a band saw tooth automatically by providing a saw-tooth passage, a saw-tooth suppling means, a saw-tooth carring means, a flash butt welding means and a polishing means, and stretching a band saw tooth over a drivi...
|
|
JPH0375932U |
|
|
JPH0371823U |
|
|
JPH0371824U |
|
|
JPH03166014A |
PURPOSE: To prevent a band saw tooth from being sandwiched in the cut channel of a work because of the inner stress of the work by causing a wedge member whose lower end portion is located above the back portion of the band saw tooth to ...
|
|
JPH03161215A |
PURPOSE: To secure sufficient sliding area even for a flat plate flap of relatively small thickness, and to obtain high linking intensity and tensile strength by fitting a projected part for linking that is formed of the same thickness a...
|
|
JPH0368728U |
|
|
JPH0368731U |
|
|
JPH0368724U |
|
|
JPH0368730U |
|
|
JPH0368729U |
|
|
JPH0368726U |
|
|
JPH03149124A |
PURPOSE: To prevent scrapping of a workpiece due to a curved cut by placing a cut curve detecting device along a cutting groove of the workpiece given a cut. CONSTITUTION: By giving a cut to a workpiece W by a band sawing machine, cuttin...
|
|
JPH03136717A |
PURPOSE: To introduce a reasonable and highly efficient cutting condition for every section during cutting, by indicating a cut length, a one tooth cutting force, a one tooth cutting degree, an entire cutting resistance and the limit val...
|
|
JPH0355115U |
|
|
JPH0344514U |
|
|
JPH0344515U |
|
|
JPH0340024U |
|
|
JPH0333023U |
|
|
JPH0373216A |
PURPOSE: To enable workpiece to be continuously cut off for an extremely long time by transferring jigs mounting the workpiece on a transfer table and stopping serially the jigs in a plurality of units to cut off the workpiece put it as ...
|
