| Document |
Document Title |
|
JPH06286672A |
PURPOSE: To improve the selection operation performance by installing a driver's seat, prime mover part, and a steering wheel which is swingable in the longitudinal direction on a traveling machine body equipped with a mower, allowing th...
|
|
JPH06288312A |
PURPOSE: To increase forward visibility and stability of machine body by eliminating the necessity for a fuel tank to be located above an engine so as to move the fuel tank downward. CONSTITUTION: An electric fuel feed pump 82 powered fr...
|
|
JPH0636992Y2 |
|
|
JPH0665175U |
[Purpose] In a walk-behind management work machine in which a handle rod is provided from the machine body to the rear and upward, only the rotary is attached to the rear side of the machine body for tilling work, or the rotary and the h...
|
|
JPH0632471Y2 |
|
|
JPH0660315U |
An elongated operating shaft supporting a tool at one end, a drive motor at its other end, and transmission means extending through said shaft to drive said tool is provided with a control handle for adjusting the holding and guiding the...
|
|
JPH0660586U |
[Purpose] Provide a standing carrier with good operability. [Constitution] The handle post 3 is attached to the front part of the flat loading platform 1, the handle post 3 is extended from a predetermined height position toward the rear...
|
|
JPH0630580Y2 |
|
|
JPH0629174Y2 |
|
|
JPH0659845B2 |
|
|
JPH0659844B2 |
|
|
JPH0628383Y2 |
|
|
JPH0626426Y2 |
|
|
JPH06197605A |
PURPOSE: To lower the center of gravity of a machine body by miniaturizing a transmission case of a self-travelling type working vehicle. CONSTITUTION: An engine E turning a crank shaft 34 downward is supported by an engine bed 2 protrud...
|
|
JPH0624306Y2 |
|
|
JPH0623509Y2 |
|
|
JPH0623510Y2 |
|
|
JPH0618825Y2 |
|
|
JPH0637081U |
[Purpose] Simplification of airframe configuration [Constitution] One end of each of the mounting frames 23, 23, which are also divided into left and right, is specially welded to the outer surfaces of the chain cases 5, 5 which are divi...
|
|
JPH0637082U |
[Purpose] A walking-type mobile farm machine that has a center of gravity in front of the single-axle axle and a loop handle that points diagonally backward and upward, without significantly increasing the production cost. Allows the ope...
|
|
JPH06135356A |
PURPOSE: To provide a running vehicle with simple structure and a low cost, while run-on-step traveling can be smoothly perforthed. CONSTITUTION: A running vehicle is formed so as to be capable of run-on-step traveling with revolution of...
|
|
JPH06125602A |
PURPOSE: To lower the machine body centroid of a walking type mobile agricultural machine equipped with an engine, a rotary working device and mobile wheels and facilitate the control operation. CONSTITUTION: A forwardly protruding rotar...
|
|
JPH06122386A |
PURPOSE: To nearly eliminate the inadvertent floating operation by extending a subpassage in the direction different from the lever operation direction on a main passage. CONSTITUTION: A raising and lowering lever 15 is horizontally shif...
|
|
JPH06115368A |
PURPOSE: To offer a walking type small electric motor car easily understandable of its forwarding and reversing state by an operator, an electric motor car capable of causing an operator to clearly identify specially the change over to t...
|
|
JPH0626401U |
[Purpose] Provide a walking electric work machine that is convenient for operation and storage. [Constitution] A walking electric work machine 1 including a work machine and a machine body 2 provided with an electric motor for driving th...
|
|
JPH0611918Y2 |
|
|
JPH068647Y2 |
|
|
JPH0615344B2 |
|
|
JPH0648193A |
PURPOSE: To prevent a torsion load from being applied to a line by placing a bush accommodating the line over a drive unit, the bush being pivotable around an axis of a central line, and aligning the axis of the central line with a verti...
|
|
JPH065683Y2 |
|
|
JPH0632151A |
PURPOSE: To perform quick advance and retreat changeover operation while checking unforeseen retreat operation by providing a changeover operation shaft for changeover between advance and retreat separately from the speed change operatio...
|
|
JPH0624201A |
PURPOSE: To easily and quickly carry out the replacing work of an auxiliary disk for prevention of lateral dislocation when the disk is replaced between the right position and the left position in the reciprocating traveling of the machi...
|
|
JPH05338563A |
PURPOSE: To set the center of gravity of a walking type cultivator on a low position, so as to improve operability. CONSTITUTION: A handle bracket 26 is fitted on the rear part side of the body of the gear case 31 of a walking type culti...
|
|
JPH0594071U |
[Purpose] When the moving wheels are moving backward, the pair of left and right idle wheels are regulated in the direct direction. [Constitution] When the shifting lever 4 is shifted to the forward position, the regulation pin 6 provide...
|
|
JPH0588202U |
[Purpose] It can be easily compact and narrowly formed, and can be advanced to narrow ridges where crops are planted for controlled tillage work. [Constitution] An input shaft (2) is erected at the upper end of the inverted V-shaped chai...
|
|
JPH05301586A |
PURPOSE: To facilitate the operation and achieve the reliable operation and the safety by connecting an electric controller for the traveling, stopping and steering operations of a cart body to the cart body by a communication cable. CON...
|
|
JPH05301585A |
PURPOSE: To reduce the fatigue caused by operation of a walking type electric- driven golf cart which is capable of traveling on the lawn, and surely prevent the lawn from being damaged by mistaken operations. CONSTITUTION: A boading ste...
|
|
JPH0580368B2 |
|
|
JPH0542650Y2 |
|
|
JPH05278491A |
PURPOSE: To improve the maneuverability of a self-traveling work vehicle, to prevent an operator from being exposed to danger, and to select a operation method arbitrarily. CONSTITUTION: An engaging lock equipment 53 is provided for a tr...
|
|
JPH0541051Y2 |
|
|
JPH0536338Y2 |
|
|
JPH0536337Y2 |
|
|
JPH0561153B2 |
|
|
JPH0557151B2 |
|
|
JPH0557150B2 |
|
|
JPH0562394U |
[Purpose] A handle mounting structure for a walking work machine that can regulate the handle orientation of models with different specifications for changing the handle orientation around the vertical axis core with only a single type o...
|
|
JPH05193530A |
PURPOSE: To provide a wheel installation structure for shift by which a wheel for shift on a walking controlling machine can easily be mounted and demounted, without using a connection part which tends to be lost and is effective for the...
|
|
JPH0555805U |
[Purpose] It is not necessary to provide a resin bush or grease on the support part of the rotatable operation lever, and the structure is simple, the manufacturing cost can be reduced, and the durability of the support part is improved....
|
|
JPH0549491B2 |
PURPOSE:To carry out clutch release operation, gripping a steering wheel, by installing a clutch release lever onto the steering wheel having a clutch lever installed and arranging the operation part and steering part at the both edges o...
|
