| Document |
Document Title |
|
JPH02140294U |
|
|
JPH0243503Y2 |
|
|
JPH02279981A |
PURPOSE: To set a size in the direction of thickness comparatively small to enable a lamination with the use of a simple device so as to allow the device to effectively act hot air on a veneer by mounting the veneer on a shelf member so ...
|
|
JPH02279980A |
PURPOSE: To allow the device to continue heat generation of a far infrared heater without stop by attaching a reflection plate and the far infrared heater to a vertically movable fixture in a furnace to release heat and allowing the devi...
|
|
JPH0243034Y2 |
|
|
JPH02270350A |
PURPOSE: To obtain a device, by which the state of the output of an ultraviolet lamp and the like is always seen easily and the optimum exchange period of the lamp and the like can be judged, by a method wherein an illuminance sensor is ...
|
|
JPH0240471Y2 |
|
|
JPH02124921U |
|
|
JPH02245155A |
PURPOSE: To satisfactorily dry the section of long pasta in contact with a rod by structuring a supporter, with which the long pasta is supported inside a tunnel-shaped dryer, as a pipe-shaped rod having a flat top surface and wing- shap...
|
|
JPH0243112B2 |
|
|
JPH0242633B2 |
The device comprises a swivel joint coupling, connecting the top plate of the product carrying plate stack to the rod of the flacon sealing cylinder-piston assembly and adapted to allow a given inclination of the top plate and hence of a...
|
|
JPH0241163B2 |
|
|
JPH02226790A |
PURPOSE: To make an apparatus small-sized and compact, and improve drying efficiency by a method wherein substrates are piled up, accommodated in a drying furnace and dried. CONSTITUTION: Substrates 4 on which circuit patterns are printe...
|
|
JPH0239227B2 |
|
|
JPH02109239U |
|
|
JPH02210445A |
PURPOSE: To increase the printing speed of a printer by arranging nozzles apart distances smaller than 10mm from a print material and setting the velocity of the flow of air in proximity to the respective nozzles higher than 100m/sec. CO...
|
|
JPH02104633U |
|
|
JPH0235912B2 |
|
|
JPH0235230B2 |
|
|
JPH0233797B2 |
|
|
JPH0227905Y2 |
|
|
JPH0289290U |
|
|
JPH0225507Y2 |
|
|
JPH0222626Y2 |
|
|
JPH0261479U |
|
|
JPH0217796B2 |
|
|
JPH0252436U |
|
|
JPH0289986A |
PURPOSE: To control the speed of a transfer mechanism precisely by a method wherein the weight of a material to be dried is measured while lifting it up from the lower part thereof instantaneously at at least three places of an initial p...
|
|
JPH0289985A |
PURPOSE: To dry a work without producing any stain due to the movement of water drips on the surface of the work by a method wherein the surface of the work is wetted by water totally while the moisture on the surface of the work is drie...
|
|
JPH0286726A |
PURPOSE: To prevent food cooking variation by setting up, near at least both ends of a carrying means, plate-like secondary emitters extending along the carrying direction so that the inner surfaces thereof represent sharp angles against...
|
|
JPH0244688U |
|
|
JPH0210955Y2 |
|
|
JPH0275883A |
PURPOSE: To reduce heat loss to be dissipated through an ampule carrier by providing in parallel a linear ampule retainer having an uneven part of a predetermined period for preventing the ampule from moving on its surface and the carrie...
|
|
JPH0257884A |
PURPOSE: To provide hay of good quality having a desired moisture content and greenness by a method wherein drying by means of microwaves and drying by means of a drying medium are alternately effected in the middle of convey ance of a s...
|
|
JPH027671Y2 |
|
|
JPH023912B2 |
|
|
JPH024672U |
|
|
JPH029475A |
PURPOSE: To form a resin coat at a speed corresponding to a production pace by placing rotary cups where cup-shaped containers for instant noodle are set and held in parallel and in a circle on the periphery of a rotor and sending the co...
|
|
JPH028274A |
PURPOSE: To dry a film coated in manufacturing of shoes with reduced energy consumption and cost, by supporting a product coated with an adhesive, colliding air jet onto the exposed coating surface at ambient temperature, and then heatin...
|
|
JPH02416A |
PURPOSE: To save energy by removing moisture from an article by moving air toward the article at high speed, allowing the air to flow along a blower, heating it and performing post-drying later while using the same air. CONSTITUTION: Air...
|
|
JPH0262Y2 |
|
|
JPH0141114Y2 |
|
|
JPH0157277B2 |
|
|
JPH0154633B2 |
|
|
JPH01273986A |
PURPOSE: To improve a drying efficiency by a method wherein a bobbin having several small holes at its circumferential surface is arranged within a high frequency drying device in a horizontal direction and the bobbin is transported whil...
|
|
JPH01270962A |
PURPOSE: To cope with various printing modes, by making it possible to select between drying processes using a hot air flowing apparatus and/or a far infrared heater by one dry booth. CONSTITUTION: When the work 16 placed on a feed means...
|
|
JPH01269894A |
PURPOSE: To permit efficient drying without generating irregularity in drying, by a method wherein a substance to be dried is arranged horizontally, both end shafts of the same are put on conveyer rolls to make it pivotable, and the rota...
|
|
JPH0135184Y2 |
|
|
JPH01149981U |
|
|
JPH01254275A |
PURPOSE: To make the title apparatus compact, by mounting many lateral feed conveyors in a drying oven in a multistage fashion and providing upper and lower recirculation conveyors performing delivery between the lateral feed conveyors. ...
|
