| Document |
Document Title |
|
JPS58196108A |
PURPOSE: To provide a rolling equipment capable of reducing its installing space and productive cost, by making the distance, between the axial centers of upper and lower intermediate rolls, approximately equal to the distance between re...
|
|
JPS58160606U |
|
|
JPS58160607U |
|
|
JPS5847242B2 |
|
|
JPS58157206U |
|
|
JPS58157210U |
|
|
JPS58148347U |
|
|
JPS58168410A |
PURPOSE: To reduce the length of a loop of hoop sharply, and to make a space to be occupied by a rolling equipment as small as possible, by providing an extraordinary low-speed outputting mechanism to a continuous cold-rolling device of ...
|
|
JPS58146127U |
|
|
JPS58143008U |
|
|
JPS58143007U |
|
|
JPS58159909A |
PURPOSE: To simplify the construction of roll chock and the supporting construction of roll, by equipping a connecting cap to a coupling case freely rotatably by restricting it in the axial direction. CONSTITUTION: The rotating force of ...
|
|
JPS58159908A |
PURPOSE: To simplify the construction of a roll chock, and to perform easily the operation of roll exchange, by transferring the retaining fucntion of the roll chock against a thrusting force to a roll coupling device. CONSTITUTION: The ...
|
|
JPS5842761B2 |
A rolling process wherein a pair of working rolls are driven at different peripheral velocities so that the peripheral velocity ratio may be varied, and the peripheral velocity ratio is so controlled that the rolling torque of each of th...
|
|
JPS58157506A |
PURPOSE: To make the construction of hollow shafts simple and to reduce costs by supporting rotors in a housing thoroughly to reduce the load of the hollow shafts and using the hollow shafts only for the rotation of circular conical roll...
|
|
JPS58128710U |
|
|
JPS58125601U |
|
|
JPS5836405Y2 |
|
|
JPS5836404Y2 |
|
|
JPS58107203U |
|
|
JPS58117334A |
A crosshead piston assembly 10 comprises a head member 18 and a skirt member 20, each of which can be secured independently to a gudgeon pin 14. The skirt member 20 has a reduced diameter upper end portion 66 which fits within a lower en...
|
|
JPS5896124U |
|
|
JPS5828649Y2 |
|
|
JPS5828647Y2 |
|
|
JPS5828648Y2 |
|
|
JPS5827191Y2 |
|
|
JPS5885405U |
|
|
JPS5825591B2 |
|
|
JPS5876309U |
|
|
JPS5823163B2 |
|
|
JPS5877634A |
PURPOSE: To measure a gap amount in a short time by on-line, by decelerating a motor, and measuring the opening and closing of a gap by inertia. CONSTITUTION: A roll 1 and a motor 2 are connected by a power transmission shaft 4 having a ...
|
|
JPS5821936Y2 |
|
|
JPS5866010U |
|
|
JPS5861305U |
|
|
JPS5814155B2 |
|
|
JPS5835017U |
|
|
JPS5832408U |
|
|
JPS5825804A |
PURPOSE: To realize arbitrary roll phase angles for the purpose of drawing of circular pipes with less angular bulging at high quality variously by providing a revolving shaft to a roll box connecting a universal joint thereto and suppor...
|
|
JPS587818Y2 |
|
|
JPS587922U |
|
|
JPS582481Y2 |
|
|
JPS586712A |
PURPOSE: To facilitate the maintenance of motors and reduce the space of a rolling yard, by arranging all roll driving motors for an X type rolling mill in one side of a stand. CONSTITUTION: The input shaft of a decelerator 4' installed ...
|
|
JPS58306A |
(57) [Abstract] Since this gazette is application data in front of an electronic application, the data of an abstract is not recorded.
|
|
JPS57207158A |
PURPOSE: To provide an alloy consisting of a prescribed percentage each of C, Si, Mn, Ni, Cr, Mo and V and the balance Fe, having high strength and toughness, and most suitable for use as the material of spindles and couplings of a rolli...
|
|
JPS57194702U |
|
|
JPS57185402U |
|
|
JPS57185401U |
|
|
JPS57190703A |
PURPOSE: To reduce installation spaces through unitization of bearings and driving mechanisms respectively by driving a pair of rolling rolls with respectively separate motors. CONSTITUTION: A pair of rolling rolls 11a, 11b are driven re...
|
|
JPS5755484B2 |
A rolling mill comprises a pair of upper and lower work rolls, upper and lower backup rolls respectively backing those work rolls, upper and lower intermediate rolls interposed respectively between the upper work roll and upper backup ro...
|
|
JPS57181407U |
|
