| Document |
Document Title |
|
JP3126965U |
To provide a cutting tool sharpening tool which can be easily used by anyone and can be sharpened safely and surely. A powdery or granular diamond 2 is uniformly fixed on an upper surface of a thin metal plate 1, and a plate-shaped magne...
|
|
JP3126972U |
To provide an extremely inexpensive hand sharpening tool for a back blade of a round sword used for woodblock printing and wood carving. The diameter of the blade portion of a used press punch or a straight shank drill having a small dia...
|
|
JP3844897B2 |
To securely prevent the wrong operation in an power tool provided with a switch for turning a power source on/off with the sea-saw operation. This switch 20 is provided with an operating member 21, a lock member 22 and an elastic member ...
|
|
JP3125814U |
To provide a file case which can be safely stored when carrying a sharpening repair file of a chainsaw. This is a file case composed of a long cylinder (8) having an internal hole (10) and a lid (18) for closing the mouth (9) thereof, an...
|
|
JP3822872B2 |
To provide a strength-reinforced brush capable of both lengthening a service life of a brush part and improving polishability, and a deburring/polishing method using the same. In the deburring/polishing method employing the strength-rein...
|
|
JP3125072U |
To provide an automobile repair polishing tool which is excellent in usability for a user and can be used particularly advantageously for repair in which it is necessary to properly use sandpapers having different counts according to a w...
|
|
JP2006224283A |
To provide a member and a method for repairing roughness having a roughness amplification function, easily, efficiently, and accurately performing detection and repair of roughness or the like of a surface of an article to be repaired ev...
|
|
JP2006159395A |
To provide a new method to surely improve sharpness of a kitchen knife simply using a file plate and (water resistant) paper file by even an amateur, and a cutting board with the file plate and the (water resistant) paper file.This metho...
|
|
JP2006150543A |
To provide an accessory belt remanufacturing tool 1 capable of easily reproducing a pulley winding face of a secularly worn accessory belt 2 in a state excellent in abnormal noise resistance.In the reproducing tool 1 for reproduce a pull...
|
|
JP2006136989A |
To provide a carpenter sand file manufacturing method capable of demonstrating high performances such as low cost, excellent convenience and usability, and high filing sharpness.Unit materials which are formed in a shape of improving the...
|
|
JP2006116699A |
To prevent an adhesive of abrasive paper with the adhesive from transfer to the sticking surface of a buffer member generated by influences of frictional heat in polishing work in a hand tool polishing a target surface with the abrasive ...
|
|
JP2006512951A |
The present invention discloses a disposable scrubbing product for use in household cleaning or personal care applications. In one embodiment, the present invention is directed to a cleaning tool including a handle and a rigid base to wh...
|
|
JP3768204B2 |
To provide a nail polishing sheet wherein a grinding and polishing layer is integrally formed on the same surface of a base fabric, thereby allowing smooth nail polishing. A nail polishing sheet 1 has a grinding and polishing layer 1a in...
|
|
JP2006088315A |
To excellently resharpen a cutter, etc. by improving the flatness of the truing surface of a grinding stone truing device and the grinding surface of a grinding stone.A sheet of plate glass is used as the base portion 2 of the grinding s...
|
|
JP3763975B2 |
To provide a top ring control device capable of detecting an abnormality when an object to be polished is polished by a top ring speedily and securely and corresponding to it properly. This top ring control device is provided with an air...
|
|
JP3759788B2 |
To provide a knife and blade polishing device of simple, inexpensive structure without using two-piece structure formed of two independent members. A comb-type structure body 10 with a plurality of groove parts 14 formed to be the openin...
|
|
JP2006501074A |
A tool for polishing knife's edges, the tool ( 1 ) comprising two oppositely positioned and co-rotating rings of elongate honing studs ( 10 ), extended at intersecting directions forming an angle (alpha) wherein the knife's edge is inser...
|
|
JP2006000950A |
To provide a method of fixing together an inner core pipe and an outer pipe of a rotary polishing roll which is formed of the inner core pipe, the outer pipe, and brushes or buffs mounted on the outer pipe, wherein the polishing roll cop...
|
|
JP2005537142A |
An abrasive tool comprising of a base portion (2), having a foam layer (3) affixed to the abrasive tool base portion, and a plastic film layer (4) affixed, bonded or glued to the foam layer. This tool is adapted to receive an abrasive ma...
|
|
JP2005536367A |
A hand held corner sanding sponge includes a backing layer of an open-celled foam material having first and second major surfaces that meet at a right angle and third and fourth major surfaces that meet at a right angle. The cross-sectio...
|
|
JP3723000B2 |
To provide an abrasive cloth and paper fixing structure capable of eliminating production of melting resin at a base plate head end part of a portable polishing device to the utmost, eliminating a sense of incongruity at the time of poli...
|
|
JP2005326250A |
To provide a cleaning sheet for probes provided with a sufficient cushion property not only when used at normal and high temperatures but also in a low-temperature environment and capable of softly and efficiently cleaning probe tips.The...
|
|
JP2005319562A |
To provide a new type of machining method replacing a method of using a wheel and supplying a usual grinding fluid from a nozzle in end face grinding of glass for a display such as an LCD wherein grinding is performed while supplying a l...
|
|
JP2005254354A |
To provide a profiling sheet material for supporting polishing material, and a polisher made of it, which are free from a danger to the human body in profiling work and from risk of disaster due to fire, dispense with a special device su...
|
|
JP2005240241A |
To provide a method for producing a high-strength polyamide fiber having excellent polishing property and durability, high-strength polyamide staple fiber and a polishing material produced by using the staple fiber.A polymer composed mai...
|
|
JP2005231025A |
To provide a knife sharpener held immovably on a table without needing an additional holding means and manufactured at a low cost.The knife sharpener is provided with a housing 1 having a surface formed as a placing surface, and an appro...
|
|
JP2005206675A |
To obtain an abrasive material that hardly damages the surface of a material to be cleaned, synergistically keeps antifouling effect, is hygienic and economical, excellently finishes a hard surface of glass, ceramic, porcelain, tile, met...
|
|
JP3679191B2 |
To enable grinding in a part other than a tip face by orienting an inorganic long fiber in which thermosetting resin is impregnated with an angle so that an end face of the fiber appears on flat faces on a surface and a rear surface and ...
|
|
JP2005193337A |
To provide a grindstone by which rough grinding and finish grinding can be executed by reducing a dead zone and by providing a grinding face for rough grinding and that for finish grinding on the same face.The grindstone is composed such...
|
|
JP2005519777A |
A device for the manual sharpening of knives and other blades having exchangeably held carbide plates. The exchangeable carbide plates of manual sharpening devices are inserted or pushed into recesses or into a reception of the device bo...
|
|
JP3628318B2 |
To efficiently polish both of a polishing surface with small recesses and a flat polishing surface by a hand-held nonwoven polishing sheet. The nonwoven polishing sheet comprises: fibers sterically and undirectionally collected and joine...
|
|
JP2005046956A |
To provide a sandpaper holder capable of performing the detail grinding of a metal mold by securely fixing and holding a sandpaper without using an exclusive sandpaper.This sandpaper holder 1 comprises a long holding bar 10 having a tape...
|
|
JP2004538165A |
An oscillating grinder (10) with a housing (12) a grinding sheet holder (14) having clamping means (20, 23; 200, 230; 334) for receiving a grinding sheet (16), whose grinding sheet ends (17, 19) can be clamped firmly to the grinding shee...
|
|
JP2004306175A |
To provide a polishing pad, which is a tool for polishing metal substituting for a wire brush, and preferably used especially for a welded part of steel, and a polishing tool using it.This polishing pad is formed of a substantially plate...
|
|
JP2004276159A |
To efficiently perform correction for the polishing surface of a grinding wheel in a short time.This grinding wheel device includes: a grinding wheel having a polishing surface for polishing a blade; a grinding wheel correction device ha...
|
|
JP2004237427A |
To provide a holder which can improve workability of sandpaper.When a sheet 6 of sandpaper has been mounted on a holder body 2 by attaching a fixing frame 4 to the holder body 2, the sheet 6 of sandpaper passes through the clearance 36 b...
|
|
JP2004229744A |
To provide a cutter which is constituted in such a manner that the blade tip part of the blade body can properly and easily be sharpened.This cutter X is equipped with the blade body 1, a handle 2 which supports the blade body 1, and a w...
|
|
JP2004209606A |
To provide a dirt remover which efficiently, completely and easily removes deposited strong water dirt and other dirts while inhibiting an object to be washed from being damaged as much as possible.The dirt remover is constituted by subs...
|
|
JP2004160636A |
To provide a cutter sharpening holder which ensures its stiffness without marring a surface of a cutter.The cutter sharpening holder 10 is formed of a metallic plate for holding an angle between a cutting edge 3b of the cutter 3 and a gr...
|
|
JP2004122344A |
To manufacture an abrasive excellent in polishing effect and inexpensive.This abrasive is made by solidifying a soft part 13 of a shell 11 by taking out the shell 11 from a raw cuttlefish of a sepiibae family and drying it in the sun for...
|
|
JP3521675B2 |
To provide a polishing tool and polishing method capable of efficiently polishing, for example, those areas which form a pin-shape like casting pin of casting metal mold and where a space sufficient for polishing cannot be secured around...
|
|
JP3512906B2 |
PURPOSE: To obtain a whetstone for a fishing hook capable of preventing damage by initial contact and injury at the end of the whetstone, being efficiently abraded while keeping an angle at the tip of the fishing hook and of being readil...
|
|
JP2004090169A |
To provide a sharpener for a cutter, simply sharpening a cutter.This sharpener for a cutter is provided with a sharpening part including: at least two plate parts 34a, 34b respectively having a polishing surface 36 on one side and dispos...
|
|
JP2004090101A |
To provide a dry polishing method for a spray coating surface for reducing the number of steps, shorten the work time, and dispensing with water to save the time and trouble required for the use of water.This dry polishing method is char...
|
|
JP2004074389A |
To provide a fake plug capable of scouring rusty things off, which is plugged into a tube into which a guitar plug is inserted so that the tube does not become rusty.The fake plug is characterized by making a cut in the plastic fake plug...
|
|
JP2004065380A |
To provide a surgical file with which a protruding bone on the curved surface of a bone and that in a gap between bones can speedily be cut to be flat.The surgical file 10 comprises a belt-like file main body 11 which is so flexible as t...
|
|
JPWO2002026446A1 |
The present invention relates to a polishing tool that polishes a repaired surface into a predetermined shape. The polishing tool of the present invention has a polishing machine body that holds a polishing material on a surface facing t...
|
|
JP2004025393A |
To provide a bristle material for a polishing brush having an excellent polishing property in dry polishing work of special steel such as stainless steel sheets and excellent in weld-bond resistance.This bristle material is formed of a m...
|
|
JP2004016400A |
To perform grinding, and a treatment in an environment of wide scope by stably holding a cutting part at a very small site in a lesion.A grinding burr to be arranged in a handpiece, and used for grinding a tooth includes: a shank part 12...
|
|
JP2003340645A |
To provide a tweezer-type contact grinding tool which can easily polish a contact while keeping a contact form even by an inexpensive and simple structure. Mutually opposite faces 21a and 22a are provided on a pair of holding portions 21...
|
