Document |
Document Title |
JPH04125654U |
|
JPH04318243A |
PURPOSE: To prevent an overrich phenomenon at quick deceleration time without using an expensive constitutional element. CONSTITUTION: An EACV5 provided in a bypass passage 4 detouring around a throttle valve 3 of a carburetor 1, first v...
|
JPH0444827Y2 |
|
JPH0444839Y2 |
|
JPH04284146A |
PURPOSE: To perform running taking refuge arbitrarily even in the case of generating a trouble in a motor by controlling an opening of an ISC valve by an accelerator opening which is electrically detected at fail time of the motor for op...
|
JPH04262063A |
PURPOSE: To provide the intake port of an internal combustion engine with an intake control valve which can prevent the problem caused by the injection fuel stuck to the wall face of a swirl port side intake passage when the intake contr...
|
JPH0454050B2 |
|
JPH0499470U |
|
JPH0452857B2 |
|
JPH0452856B2 |
|
JPH0452391B2 |
In an air assist device of a fuel injection type internal combustion engine, having an air assisted injector provided close to a nozzle thereof with an adapter constituting an assist air introducing portion, in which assist air introduce...
|
JPH04209966A |
PURPOSE: To prevent lubricating oil from infiltrating into a fuel injection device so as to well maintain injection performance by interposing a gas-liquid separator in a compressed air passage reaching the fuel injection device from an ...
|
JPH0482350U |
|
JPH04187818A |
PURPOSE: To obtain a high inertia supercharging effect due to a pulse of low frequency by providing a control valve closing means for closing a control valve when it is judged that an engine speed is lower than a predetermined engine spe...
|
JPH0476954U |
|
JPH0426684Y2 |
|
JPH0426687Y2 |
|
JPH0437261B2 |
|
JPH0468270U |
|
JPH0436258B2 |
|
JPH0465951U |
|
JPH0429869B2 |
|
JPH0422142Y2 |
|
JPH0421001Y2 |
|
JPH04136466A |
PURPOSE: To improve the restarting performance by installing a solenoid valve for opening/closing-controlling the opening of an air introducing pipe whose one edge is connected to an engine to the atmosphere and opening the solenoid valv...
|
JPH04132841A |
PURPOSE: To prevent any increase in brake stepping force of a brake servo device by increasing a load which is formed in an intake port when brake operates in the low load operation condition including idling time of an internal combusti...
|
JPH0449654U |
|
JPH0417777Y2 |
|
JPH0417793Y2 |
|
JPH0444461U |
|
JPH0440115U |
|
JPH04101031A |
PURPOSE: To secure the optimum air/fuel ratio following a change in an intake air flow rate even at transient driving by delaying an opening/closing motion of a first opening/closing valve than a required opening/closing motion by a pred...
|
JPH0413381Y2 |
|
JPH0494455A |
PURPOSE: To realize good atomization of fuel at the time of high load low speed operation with a simplified structure by press-feeding air in the downstream part of an assist air supply path synchronized with injection action when an eng...
|
JPH0434463U |
|
JPH048295Y2 |
|
JPH0463927A |
PURPOSE: To suppress malfunction of an engine in accordance with a slight operation of accelerator by receiving a signal from a throttle valve opening variation detection means, and compensating it to increase an engine output when the o...
|
JPH0419641U |
|
JPH0419655U |
|
JPH0417153U |
|
JPH0417152U |
|
JPH0441949A |
PURPOSE: To effectively prevent overlean of intake gas by forbidding a deceleration increase quantity of the intake gas for a specified time when a bypass valve is closed in a device which opens a bypass valve for the specified time at t...
|
JPH0436053A |
PURPOSE: To greatly reduce pumping loss by providing a limited open rate setting means for setting according to detected engine speed the maximum limited open rate at which pressure inside a combustion chamber is roughly at its maximum w...
|
JPH045807B2 |
PURPOSE:To prevent ignition timing from coming into an excessive spark advance state, by coupling an idle-up device with an actuator, while opening an on- off valve in time of idling. CONSTITUTION:In time of idling, a solenoid for an atm...
|
JPH044447B2 |
|
JPH041340Y2 |
|
JPH0411965A |
PURPOSE: To control vibration of the vibration member by equipping the ultrasonic wave vibration member, an ultrasonic wave generating means and a liquid supply valve, a liquid heating means and a temp. detecting means. CONSTITUTION: An ...
|
JPH041177B2 |
|
JPH041670U |
|
JPH041468A |
PURPOSE: To keep off any hunting in and around a control valve selecting point due to flow characteristic variations within the tolerance of each control valve by installing an opening clamp means which clamps the opening of a control va...
|