Document |
Document Title |
JPH0320124A |
PURPOSE: To provide easy and quick removal and refilling of oil by connecting a transfer pipe to a variable flow type fluid coupling and its auxiliaries, communicating its lower end with an oil storage tank, and communicating the oil sto...
|
JPH034775B2 |
|
JPH039127A |
PURPOSE: To keep the circulation amount of fluid without degrading the strength of an impeller outer shell by having a ring shield 21 arranged in an adjacent manner to the inner periphery side of an impeller blade and shielded with an oi...
|
JPH039126A |
PURPOSE: To shorten a size in an axial direction by arraying a tourus, a damper and a turbine hub in sequence on the outer periphery side in a radial direction and spline-connecting both of the driven plate of the dumper and the turbine ...
|
JPH039124A |
PURPOSE: To emit generated heat to the outside sufficiently by forming an oil passage, through which an oil room between an impeller and a turbine communicates with an oil room between the turbine and a lockup clutch, on a turbine outer ...
|
JPH039125A |
PURPOSE: To improve lockup response by arranging thrust bearings between an impeller hub and a turbine hub and forming a channel communicating with the inner and the outer periphery sides thereof in the opposite end face of the impeller ...
|
JPH0245536Y2 |
|
JPH0245358Y2 |
|
JPH02274630A |
PURPOSE: To improve durability by moving a propeller shaft in the axial direction to connect a clutch through relative rotation between a casing and an axial flow propeller, and increasing transmitting torque corresponding to increase of...
|
JPH02127827U |
|
JPH02245523A |
PURPOSE: To aim at improvement of efficiency of a fluid coupling by providing a temperature regulating valve for regulating flow quantity at an operating oil inlet according to the temperature of oil at an operating oil outlet in an oper...
|
JPH0240886B2 |
|
JPH0225003Y2 |
|
JPH0225002Y2 |
|
JPH02159425A |
PURPOSE: To moderate a sudden deceleration during coasting travel to smoothen power transmission in a fluid coupling inserted and used in the transmission system of a continuously variable transmission, etc. by tilting a pump impeller bl...
|
JPH0213720Y2 |
|
JPH0251730U |
|
JPH0233935U |
|
JPH0246349A |
PURPOSE: To avoid efficiency loss and to make manufacture simple and low in cost by welding a blade to the surface of an inner and/or outer casing shell facing the blade side. CONSTITUTION: A blade 2 is welded to the surface of an inner ...
|
JPH022421Y2 |
|
JPH026825U |
|
JPH0144810Y2 |
|
JPH01299324A |
PURPOSE: To insure constant supply of lubricating oil to a flash tube and to prevent the damage of a sliding surface by providing a lubricating oil supplying mechanism with a back flow preventing valve on the flash tube sliding part, for...
|
JPH01166139U |
|
JPH01269757A |
PURPOSE: To obtain large output torque even if the difference of the rotation between an input shaft and an output shaft by providing a speed increasing mechanism which increases speed and charges the difference of the rotation between a...
|
JPH01238764A |
PURPOSE: To prevent malfunction or generation of reverse torque by connecting drive pinions on high and low speed sides and flexible shafts on high and low speed sides with a rigid coupling while performing the automatic interlock of sco...
|
JPH01164859A |
PURPOSE: To prevent a gap from being produced between a reed piece part and a slit into which the reed piece part is inserted, by setting the width of the slit to be narrower than the thickness of the reed piece part, by forming a cut an...
|
JPH0127398B2 |
|
JPH0115962Y2 |
|
JPH0117011B2 |
|
JPS6439940U |
|
JPS6411848B2 |
|
JPS6410693B2 |
|
JPS6410692B2 |
|
JPS63196858U |
|
JPS6363788B2 |
|
JPS6346764Y2 |
|
JPS63289334A |
PURPOSE: To make a controller have both torque control and clutch functions by normally opening an external discharge port of hydraulic fluid to the outer circumferential part of a housing body, and installing control part, altering an i...
|
JPS63265727A |
A drive comprising a power dividing unit (1) located between the drive shaft (m) and the driven shafts (a, p) and designed to transmit the torque on the drive shaft to each driven shaft in such a manner that the torques acting on each of...
|
JPS63129724U |
|
JPS63199933A |
PURPOSE: To perform continuously variable speed control by using an electrical fluidity fluid that changes its viscosity according to voltages applied as an internal fluid of a hydraulic transmission device and by changing the voltages a...
|
JPS63186041A |
In order to insulate sound from vibrations or oscillations of an internal-combustion engine from being transmitted through solid bodies to a connected drive element, a hydrodynamic transmission (3) is used which has a resilient bearing m...
|
JPS63163067A |
PURPOSE: To easily control the rate of transmission of energy, by fitting an axial member into a cylinder member while providing a labyrinth in a connection surface of the fitted members and increasing a pressure of fluid by the pumping ...
|
JPS6333013B2 |
|
JPS6333014B2 |
|
JPS63501093A |
A fluid-operated transmission device has an impeller mounted within an input chamber which is driven by a motor or other motive source. A variable-speed rotor is positioned within an output chamber, the volume of which is selectively adj...
|
JPS6353936U |
|
JPS6349050U |
|
JPS6348052U |
|
JPS6336752U |
|