| Document |
Document Title |
|
JPH08281614A |
PURPOSE: To stick seamlessly a decorative material on the surface of a channel and in the longitudinal direction of the end face by injecting a glue into the channel formed in the vicinity of a rear face decorative material on the ground...
|
|
JPH08267686A |
PURPOSE: To provide a polyester sheet with reduced likelihood of the occurrence of drawdown, a deflection of thickness and a cloudiness of a vessel, and having various heat forming conditions. CONSTITUTION: The main repeating unit is con...
|
|
JPH08267597A |
PURPOSE: To obtain a wood panel like polyolefinic resin panel, especially, a thick-walled wood panel like polyolefinic resin panel having a wooden feeling similar to a natural panel material. CONSTITUTION: A polyolefinic resin panel is f...
|
|
JPH08267598A |
PURPOSE: To inexpensively obtain an illumination U-shaped display panel emitting light from five surfaces by arranging a clamp frame clamping a thermoplastic panel member and having a recessed wood mold fixed to the inside thereof and ar...
|
|
JPH08260331A |
PURPOSE: To obtain a high-strength network web strong in one direction, by slitting an ultrahigh molecular weight polyolefin film in a specific state and stretching the slit film in the slitting direction, useful as various reinforcing m...
|
|
JPH08258170A |
PURPOSE: To obtain a sheet of superior resistance to chemicals and recycling properties as a refrigerator interior sheet by constituting a resin component containing a copolymer graft copolymerized as an essential component which is comp...
|
|
JP2539382B2 |
PURPOSE:To obtain a good liquid crystal film, by employing co-extrusion film manufacturing method. CONSTITUTION:An intermediate layer is made of a thermotropic liquid crystal resin layer and outer layers are made of a thermoplastic resin...
|
|
JPH08253680A |
PURPOSE: To obtain the subject composition containing an aromatic polyethersulfone in a specific solvent system at a specific ratio, excellent in film peeling properties from a supporting base plate upon its casting and stability in stor...
|
|
JPH08252800A |
PURPOSE: To manufacture a resin sheet of sharp cut section without generating chips by bringing a blade whose temperature is higher than that of the resin sheet by the prescribed value into contact with this resin sheet while the tempera...
|
|
JPH08253646A |
PURPOSE: To obtain a tape which resists against breaking by rewinding tension in processing but is readily broken by hand without using any cutter, and thus improving working efficiency, by mixing two or more kinds of polyvinylchlorides(...
|
|
JPH08252869A |
PURPOSE: To prevent contamination due to adhesive of a material to be processed and to easily position the workpiece by recessing the predetermined part of an air permeable sheet used to adsorb and fix. CONSTITUTION: The air permeable sh...
|
|
JPH08509254A |
The present invention is directed toward a water vapor responsive self sealing thin film which is formed from a blend of at least about 75 weight percent of a water dispersible polymer; from about 0.5 to about 5 weight percent of a xerog...
|
|
JPH08248201A |
PURPOSE: To suppress optical strain by projecting a light ray vertically to a film, transmitting the light through the film to the rear and controlling the difference in luminance between the transmitted light rays at the places a specif...
|
|
JP2536902B2 |
|
|
JPH08240715A |
PURPOSE: To obtain a polarizing film high in contrast by uniaxially orienting a specific polyvinyl alcohol film, by a dry system and applying the adsorption/ orientation, then applying a high temp. boric acid-containing aq. solution trea...
|
|
JP2533888B2 |
A process of manufacturing a roll of continuous synthetic thermoplastic film consisting of extruded flat film or of extruded blow-formed and flattened tubular film in which the thickness of the film is measured over the width of the film...
|
|
JPH08230062A |
PURPOSE: To obtain a sheet like absorptive molded object having rigidity sufficient to support itself by using synthetic pulp and a composite fiber. CONSTITUTION: A thin plate-shaped absorbing material having absorptive property is const...
|
|
JPH08231834A |
To obtain a thermoplastic resin composition which is biodegradable and is inflation moldable, by mixing a specific biodegradable polyester with a specific polymeric auxiliary component with polar groups and polar lubricants compatible wi...
|
|
JPH08230970A |
PURPOSE: To obtain a recording medium set which can preserve recorded images for a long time with its quality maintained by providing a recording medium having an ink receiving layer and a storage bag including a means for sealing a bag ...
|
|
JPH08230063A |
PURPOSE: To obtain a polymeric film uniform in characteristics in its lateral direction. CONSTITUTION: In a polymeric film manufacturing process wherein a film molded in a state having a volatile component or capable of generating reacti...
|
|
JPH08225662A |
PURPOSE: To obtain a good-isotropy β-crystalline polypropylene synthetic paper for use in high-speed offset printing by crystallizing a film comprising a crystalline propylene polymer and a tetraoxaspiro compd. blended therewith as a nu...
|
|
JPH08208895A |
PURPOSE: To obtain a resin composition suitable for producing stretch packaging films good in appearance, rich in flexibility and excellent in deformation recovery. CONSTITUTION: This resin composition comprises (A) 70-97wt.% of at least...
|
|
JPH08197672A |
PURPOSE: To obtain a base material film for photographic film plate making, a base material film with high dimensional stability which is used appropriately as a support of an original picture film for a printed wiring substrate, etc., a...
|
|
JP2520774B2 |
A process for producing cellulose triacetate films that is capable of not only suppressing the growth of foreign matter on transport rollers, but also markedly reducing the necessary number of cleaning operations. The process includes st...
|
|
JPH08192464A |
PURPOSE: To provide a polyester heat-shrinkable film having heat shrinkability well-balanced longitudinally and laterally and having clean finish appearance not generating a defect such as wrinkles, strain or shrinkage irregularity at th...
|
|
JP2517562B2 |
|
|
JPH08188486A |
PURPOSE: To provide a method to promote effective and uniform curing even in the cases of vertical, slant and downward surfaces of concrete and to enable early removal of formwork by putting a specific curing sheet on the placed surface ...
|
|
JPH08188955A |
PURPOSE: To obtain a network nonwoven fabric by forming notches provided in a film in a nonthrough state, then drawing the film and thereby converting the notches in a through state. CONSTITUTION: Many independent notches (1a) in a nonth...
|
|
JPH08187824A |
PURPOSE: To obtain a sheet, into which the tip of a writing utensil does not bite which is excellent in writing quality and suitable for desk mat and table mat by a method wherein the relationship between the amount of plasticizer to vin...
|
|
JPH08187790A |
PURPOSE: To provide a long synthetic resin sheet formed by taking up a continuous synthetic resin sheet in a roll form, prevented from the rising at both end parts of a roll even if taken up in a roll form and generating no undulation ph...
|
|
JPH08188275A |
PURPOSE: To convert linear movement into rotational movement of a roller by means of a proper power by a method wherein at least one mechanism consisting of a feed roller arranged on one and the same rotary shaft as that of a driven pull...
|
|
JPH08183084A |
PURPOSE: To obtain a uniform sheet thickness as well as keep and adjust a product width without bringing a machine equipment to a halt and enhance a quality and a material yield by providing a pair of deckles for changing a T-die outlet ...
|
|
JPH08506610A |
Disclosed are (1) a thermoplastic elastomeric film comprised of an elastomeric arene-diene block copolymer and particular ethylene/ alpha -olefin copolymers having low ethylene crystallinity and (2) the process of preparing films thereof...
|
|
JPH08174695A |
PURPOSE: To obtain a plastic film which has excellent optical characteristics near those of glass and can be molded in a desired thickness by allowing remelted matter of thermoplastic resin molded form to flow down from a slit having a g...
|
|
JPH08176383A |
PURPOSE: To obtain a polyvinyl chloride sheet having radiation resistance useful for packing a tool for medical treatment, slightly changing in color with the lapse of a long period of time against radiation of cobalt 60-γ rays and havi...
|
|
JPH08174696A |
PURPOSE: To provide a method for manufacturing a printed olefinic resin sheet having excellent productivity and attaining sufficient adhesive force of a print layer and the sheet by transferring. CONSTITUTION: A transfer roll is so fed t...
|
|
JP2513669B2 |
|
|
JPH08169058A |
PURPOSE: To obtain a low-cost decorative material in which an effective craze pattern is formed for interior finishing by disposing a colorless transparent or colored thermoplastic resin lump and a thermoplastic resin sheet having an exc...
|
|
JPH08160226A |
PURPOSE: To decrease the thickness of light guide plate from the side edge part on the side of a light source to the other side edge part with a desired slope by adjusting the tilt angle of the pressing surface part of one mold. CONSTITU...
|
|
JPH08160567A |
PURPOSE: To provide a film for base material for photography which is constituted of polyethylene-2 and 6-naphthalate and rarely generates fogging when used as a photographic film and its manufacturing method. CONSTITUTION: The film for ...
|
|
JPH08156117A |
PURPOSE: To provide a synthetic resin sheet with both end chucks wherein a chuck part and a sheet part which meet respective different requests of the chuck part and the sheet part, are simultaneously integrally molded. CONSTITUTION: A c...
|
|
JPH08156120A |
PURPOSE: To obtain a sheet which is excellent in weather resistance excellently in film thickness without impairing intrinsic features of a polycarbonate resin by a method wherein a polycarbonate sheet is extruded from a sheet extruder h...
|
|
JPH08156122A |
PURPOSE: To enable blade tip ends to be set for correct trimming positions by forming recessed grooves for blade tip end insertion along predetermined parts to be cut of a long skin material surface in a plastics long skin material havin...
|
|
JPH08156121A |
PURPOSE: To obtain an easily tearable film with a good transparency and folding property by forming it with a composition containing a polyalkyleneterephthalate, a styrene polymer, and a polyether containing a repeating unit represented ...
|
|
JP2506447B2 |
|
|
JPH08151403A |
PURPOSE: To produce a platy polymer advantageous in production cost and capable of reducing polymerization time and energy consumption by adding a polymerization initiator to a methyl methacrylate syrup, feeding the resulting syrup to a ...
|
|
JPH08150677A |
PURPOSE: To provide a retroreflection display film in which brightness can be obtained by retroreflective light generated by irradiation of the solar rays or light of automobile, lighting from the inside or back face can be eliminated, l...
|
|
JPH08505426A |
Films prepared from aqueous dispersions of block copolymers, optional diluents and surfactants corresponding to the formula: A-B-Xm-(B-A)n wherein each A is a polymer block of a monovinylidene aromatic monomer and, optionally, a conjugat...
|
|
JPH08150667A |
PURPOSE: To provide a resin panel material and a resin structure generating no atmospheric pressure difference due to air streams and not damaged. CONSTITUTION: A resin panel material 1 is obtained by forming a large number of protruding...
|
|
JP2503007B2 |
|
