| Document |
Document Title |
|
JP3690783B2 |
To meet needs of such installation of a cylinder on the roof of buses as poses no problems of strength. A cylinder installing mechanism comprises a plurality of roof frames 5 arranged on the interior side of a roof 4 of a bus 1 perpendic...
|
|
JP3690775B2 |
To further lower the ground height of the floor surface of a low-floor bus and to make daily inspection and maintenance convenient by providing a hole section on a second floor at the position above the expansion section of a rear shaft,...
|
|
JP3677891B2 |
To provide inspection opening structure for a vehicle reducing deformation of an inspection opening, provided at a vehicle body for inspection and maintenance of underfloor equipment, at the time of external force acting upon it so as to...
|
|
JP3675714B2 |
To prevent the occurrence of a space in a joint part when two plates having flanges formed by bonding the plate are joined with each other. The plate 50 has the flange 52b formed by bonding the plate, the flange 52c that is substantially...
|
|
JP2005193782A |
To provide a getting-on/getting-off supporting device capable of allowing elderly persons, children, physically-handicapped persons or the like to easily get on/get off a vehicle such as a bus, and ensuring the safe traveling of the vehi...
|
|
JP3672445B2 |
To provide body structure of a bus mounted with a CNG(compressed natural gas) engine solving a problem of heat being confined inside in the case of covering a cylinder with a cover member. This body structure of a bus mounted with a CNG ...
|
|
JP3664438B2 |
To provide an opening/closing support device for a lid capable of utilizing the whole surface of the front opening 30 of a trunk body 23 as the space for taking in and out a luggage and holding the lid 15 by approaching the vehicle body ...
|
|
JP3664423B2 |
To provide an attaching structure of an air spring and the structure of a front fender for increasing the width of a passage of a cabin in the vicinity of the front axle of a bus in which the driven front axle is suspended by the air spr...
|
|
JP3652891B2 |
To ensure as many passengers capable of riding on a four-wheeled vehicle as possible by arranging a fuel tank along an inner wall face of a side wall of the four-wheeled vehicle. A fuel tank 25 on right side and a fuel tank 26 on left si...
|
|
JP2005104390A |
To heighten the workability of fitting a harness by securing the rigidity of a window pillar without any increase in size.The window pillar 10 is constructed by a hollow member having a recessed closed section, the wall surface of which ...
|
|
JP2005081846A |
To simplify a laying path of a pipe and a harness arranged under a floor of a passenger compartment of a bus.A gutter-like laying passage 1 along the lower surface of a floor plate of the passenger compartment of the bus is disposed from...
|
|
JP2005081847A |
To prevent the entering of water into a trunk room provided between a front wheel house and a rear wheel house of a bus by simple structure.In this bus vehicle, the trunk room 8 is formed on the lower side of a floor plate of a passenger...
|
|
JP3626859B2 |
|
|
JP3626078B2 |
|
|
JP2004359142A |
To secure a sufficiently wide baggage room and to secure an appropriate margin of the deflection of a weather strip by a relatively simple constitution.The baggage room 13 is provided at a rear part in the advancement direction of a bus ...
|
|
JP3599075B2 |
To ensure a sufficiently long impact absorptions stroke by a method wherein a center beam whose front end is coupled approximately to the central part of a front end cross member and a rear end is coupled to a position situated above the...
|
|
JP3596277B2 |
|
|
JP2004322819A |
To provide a low-floor bus allowing passengers including elderly people or the like to move smoothly on the floor surface of the passenger cabin.Wheel bases are set long without altering vehicle overall length, a front door 36 and a rear...
|
|
JP3585322B2 |
To arrange a muffler at a prescribed height without increasing a height of an engine mount while preventing the thermal damage on a transmission, etc. In a rear engine vehicle in which an engine and a transmission are mounted in the vehi...
|
|
JP2004532764A |
Adjustable fastening element intended to be fitted to an end region of a transverse member of a vehicle chassis. The fastening element takes the form of a U-section element with a web portion of preferably uniform width and with mutually...
|
|
JP3581220B2 |
|
|
JP2004291755A |
To provide a seat of a personnel transportation vehicle such as a bus and a train which enables elderly people and physically-disabled persons, particularly crippled persons, to easily sit down and stand up.The structure of a seat device...
|
|
JP2004291756A |
To increase a passageway width by relocate a part of tire housing formed in the upper part of the floor of a vehicle such as a bus.The tire housing is divided into two parts along the moving direction of a vehicle: a first tire housing (...
|
|
JP2004291757A |
To enable people with visual impairment to safely and easily know the position and move in a vehicle.An information sign leading to an exit door 6 is placed on a passageway floor 40 of a vehicle. The information sign is preferably a guid...
|
|
JP3575250B2 |
To easily and smoothly assemble a compact bus or the like, by mounting a flange part projecting outward in a car width direction, on a front pillar of a vehicle, and fixing a front edge part of a side panel forming a side wall shell plat...
|
|
JP3577437B2 |
|
|
JP3561377B2 |
|
|
JP3552049B2 |
|
|
JP3545724B2 |
To provide a low-priced structure of an end cross for a vehicle causing little deformation of chassis frames even in remounting an engine, detached from brackets for maintenance, to the brackets attached to the respective chassis frames....
|
|
JP2004156437A |
To provide a handrail and a structure having this handrail for allowing even an aged person and a disabled person with weakened grasping power to easily grasp the handrail without slipping the hand.This handrail T1 has a handrail body 1,...
|
|
JP2004130898A |
To provide a vehicle lightening load on the movement in the vehicle using an assist seat capable of assisting an occupant's sitting or leaving action.A bus 1 is equipped with a getting on/off area 5 at the side of the vehicle body and th...
|
|
JP2004098880A |
To provide a bus enabling the formation of at least three independent compartments therein.A two-storied portion 13 is formed between a front axle 1a and a rear axle 1b of the bus 1. A first compartment 16 and a second compartment 17 are...
|
|
JP3503733B2 |
To provide a supporting device for a bus fuel tank which is inexpensive and lightweight and which is capable of easily absorbing a dimensional error produced between a chassis frame and an outer plate. A supporting device for a bus fuel ...
|
|
JP3494547B2 |
To facilitate utilization of a seat on tire houses by lessening the projection on the axle in a cabin of a bus as much as practicable. Steps 5 and 6 are formed in that part of the over-part of tire houses 3 and 4 projecting into a cabin ...
|
|
JP2004025918A |
To provide a noise reduction device to be very high in sound-absorption efficiency and capable of efficiently reducing noises generated by a vehicle and a train in particular while running.A plurality of sound absorbing devices 1 are att...
|
|
JP3475907B2 |
To provide a connecting structure for panels capable of sticking a plurality of shapes each having a recessed groove or a protruded stripe to be male/female-coupled at a coupling section with uniform strength. In a panel obtained by stic...
|
|
JP3475698B2 |
To provide a frame structure for a bus whereby seating in a seat can be facilitated without causing an increase of cost and without narrowing a width of a passage in a car room. In a frame structure for a bus comprising a frame member 3 ...
|
|
JP3473721B2 |
PURPOSE: To decrease man-hour for processing parts, prevent appearance from being deteriorated over a long use because of little damage even if the baggage of an occupant or the like interferes with the corner of a cabinet body or a top ...
|
|
JP3470778B2 |
PURPOSE: To accomplish reduction in a burden of a crewman or a passenger and improvement in safety during getting on and off a bus. CONSTITUTION: In a side part of an entrance 10a with steps 11 in a bus 10, a getting on and off helping o...
|
|
JP3468361B2 |
To lock a seat at emercrency exit assuredly on a floor of bus according to an input from a seat belt at the time of colllision for mounting the seat belt on the seat at emergency exit to be fastened and to be released easily at the time ...
|
|
JP3460505B2 |
To suppress the amount of deformation of a vehicle body when the front end part of an outer wall part of the vehicle body is put into contact with the other vehicle, the side wall or the other facilities of a road. Between a pair of firs...
|
|
JP3443601B2 |
To improve the appearance of a cabin by drastically reducing the fitting works. A cooler duct 17 extending in the front/rear direction is fitted in a cabin of a bus 10, which has a luggage rack 12 erected in the lower part of a plurality...
|
|
JP3443329B2 |
To provide a structure composed of an extruded light metallic section and a composite panel light in weight to be combined with the aforesaid section. A composite panel 37 has a plastic core 32 combined with outer sheets 33 and 34 made o...
|
|
JP2003237350A |
To provide a floor structure of a vehicle, capable of giving a feeling of heating to a seated person regardless of the installation position of a seat installed on a raised floor surface.A bus 1 for sending and receiving infants has a ra...
|
|
JP3432615B2 |
PURPOSE: To provide frame structure having mobility and high strength, with the strength of the frame structure of an engine loading part increased, in the frame structure of a low floor bus with a horizontal engine on board. CONSTITUTIO...
|
|
JP3433311B2 |
To prevent damage to a hanger member from cutting, breakage and the like and simplify the mounting of the hanger member by increasing the strength of the hanger member coupled to a hanger support pipe. A hanger support pipe 1 arranged ho...
|
|
JP3426501B2 |
To reduce the weight of a bus while restraining the displacement to the frontside of a floor board easily by constituting so that the floor board is folded from its brittle part to the upperside when the displacement occurs to the vehicu...
|
|
JP2003191843A |
To provide a low-cost simple structure allowing to follow various moves of an articulated car body and having a short length in the car body advancing direction even when a passage peripheral wall is constituted of hard decorative boards...
|
|
JP3416625B2 |
To lighten the weight of an intermediate frame used for a low-floor bus and to improve the productivity. When the intermediate frame 3 connecting a front side support portion 1 supporting front wheels to a rear side support portion 2 sup...
|
|
JP3405455B2 |
To smoothly move a wheel chair between a floor face and a slope board by covering a clearance between the slope board and the floor face by an opening/closing cover in projecting the slope board. A getting-in/off entrance 10b of a vehicl...
|
