| Document |
Document Title |
|
JPS6339431Y2 |
|
|
JPS6339432Y2 |
A piston seal device for a reciprocating compressor, having a piston slidably mounted in a cylinder bore and having a circumferential groove, and a resilient piston ring fitted in the circumferential groove of the piston and sealingly en...
|
|
JPS6332933Y2 |
|
|
JPS6340943B2 |
|
|
JPS6339795B2 |
|
|
JPS63186866A |
PURPOSE: To improve the erosion resistance of the moving vane of a steam turbine and to extend the service life thereof, by forming a hard film consisting of nitride of Ti, Si, B, etc., onto the surface at the front end of said moving va...
|
|
JPS6338552B2 |
|
|
JPS6338554B2 |
|
|
JPS63177210A |
PURPOSE:To improve the load fluctuation characteristics by connecting a transformer containing a resonance capacitor and a primary winding of a magnetic leakage transformer in series to the primary side of a constant voltage device toget...
|
|
JPS6325339Y2 |
|
|
JPS6325348Y2 |
|
|
JPS6325341Y2 |
|
|
JPS6334317B2 |
|
|
JPS63162974A |
A hydraulic to pneumatic power transfer unit which converts a high pressure oil flow into a flow of high pressure air by means of three stages of piston pumps. The first stage includes a pair of linked pistons (11,14) of substantially eq...
|
|
JPS6323591Y2 |
|
|
JPS6323597Y2 |
|
|
JPS6330506B2 |
An engine driven vacuum pump combining a two-stage, low noise demountable pump assembly with a camshaft driven eccentric drive arrangement having internal oil distribution and pumping means for lubricating the drive and pump pushrod elem...
|
|
JPS6320864Y2 |
|
|
JPS6320865Y2 |
A variable-delivery compressor of a swashplate type having compression chambers wherein compression is effected by reciprocating movements of double-headed pistons slidably engaging a rotating swashplate in a cylinder block. The cylinder...
|
|
JPS6327554B2 |
|
|
JPS6380327U |
|
|
JPS6318785Y2 |
|
|
JPS6369781U |
|
|
JPS6338679U |
|
|
JPS6310315B2 |
PURPOSE:To enable efficient operation without wasteful running of the compressor and to extend its life by providing a means to have part of the discharge valves among multiple number of the same displaced to the open position and normal...
|
|
JPS6310316B2 |
|
|
JPS6345479A |
PURPOSE: To prevent the deterioration of quality and change of shape of the basic material by forming a surface hardened layer into which gas ions are introduced onto either the sliding contact surface of a slipper for a swash plate or t...
|
|
JPS636470Y2 |
A refrigerant compressor having pistons reciprocated in respective cylinders by a wobble plate driven by an input rotor which is secured on a drive shaft, in which improved refrigerant gas flow within the housing is achieved. A balance h...
|
|
JPS6341677A |
PURPOSE: To improve a pull-down characteristic which is the lowering speed of crank chamber temp. at the time of starting by delaying the pressure response of a pressure response part in a control valve mechanism to suction pressure chan...
|
|
JPS6338691A |
PURPOSE: To restrict a pressure drop of refrigerant gas in respective chambers, by communicating respective intake passages or intake chambers each other in both cylinders on and below a partition plate of an compressing element. CONSTIT...
|
|
JPS6329067A |
PURPOSE: To make it possible to sustain the maximum stroke of a piston until the characteristic of cooling for the passenger's compartment of a vehicle reaches a predetermined value, by providing an actuator adapted to hold a control val...
|
|
JPS634027B2 |
|
|
JPS634026B2 |
|
|
JPS632622Y2 |
|
|
JPS632625Y2 |
|
|
JPS6245090Y2 |
|
|
JPS62240481A |
(57) [Abstract] Since this gazette is application data in front of an electronic application, the data of an abstract is not recorded.
|
|
JPS6240130Y2 |
|
|
JPS6246705B2 |
|
|
JPS6244144B2 |
A mechanical seal mounted in a compressor comprises a rotating sealing ring, a stationary mating ring and means for pressing the sealing ring against the mating ring. The mating ring is of hardened bearing steel.
|
|
JPS6244107B2 |
|
|
JPS6242159B2 |
In a swash-plate type compressor, a partition wall, which separates a suction passageway extending through the cylinder block and the valve plates from the swash plate chamber, has its lateral wall formed with a refrigerant gas inlet ope...
|
|
JPS6240557B2 |
In a swash-plate type compressor, a refrigerant gas deflecting wall is formed in a suction passageway extending through the cylinder block and the valve plates, the deflecting wall extending substantially at right angles to the direction...
|
|
JPS6239272B2 |
|
|
JPS6239273B2 |
|
|
JPS6231673Y2 |
|
|
JPS6232356B2 |
|
|
JPS6298782U |
|
|
JPS6227272B2 |
A swash plate type compressor comprising a plurality of cylinder bores and pistons, a swash plate chamber wherein a swash plate for reciprocating the pistons within the cylinder bores is fixed to and rotated with a drive shaft, at least ...
|
|
JPS6227273B2 |
|
