| Document |
Document Title |
|
JPS6221996B2 |
|
|
JPS6218755B2 |
|
|
JPS6282283A |
PURPOSE: To make it possible to maintain the intake pressure constant, by absorbing the compression reaction into a spring resisting a negative moment imposed on a swash plate, when the variation of the intake pressure to a crankcase pre...
|
|
JPS6211194B2 |
|
|
JPS629749B2 |
|
|
JPS628391Y2 |
|
|
JPS628392Y2 |
|
|
JPS625659Y2 |
|
|
JPS626116B2 |
|
|
JPS624705Y2 |
|
|
JPS622539Y2 |
|
|
JPS627983A |
PURPOSE: To switch capacity in a moment by switching the acting pressure applied into a pressure acting chamber by a control valve operated by the pressure difference between before and behind the throttle part of a suction conduit, thus...
|
|
JPS62173U |
|
|
JPS61291782A |
PURPOSE: To supply smoothly securely lubricating oil to a drive chamber such as swash plate chamber in any conditions of continuous running by providing a bypass path opposed to a communicating path of a spool valve. CONSTITUTION: A suct...
|
|
JPS6160272B2 |
|
|
JPS61286591A |
PURPOSE: To keep pressure in the crank chamber of a variable capacity compressor always at a predetermined level for good response and improve the controllability of capacity by letting said pressure control each open/close valve at a pa...
|
|
JPS6158672B2 |
|
|
JPS61198584U |
|
|
JPS6143981Y2 |
|
|
JPS61194788U |
|
|
JPS6156433B2 |
|
|
JPS61192579U |
|
|
JPS61192581U |
|
|
JPS6155637B2 |
A swash plate type compressor for use in air conditioning systems operating with a refrigerant gas in which lubricating oil is previously mixed, comprises a plurality of cylinder bores and pistons, a swash plate chamber wherein a swash p...
|
|
JPS6155638B2 |
|
|
JPS61268877A |
PURPOSE: To permit the smooth return from the small capacity operation state to the large capacity operation state by specifying the position of formation of the opened port on the crank chamber side of a bypass release hole switch commu...
|
|
JPS61265366A |
PURPOSE: To improve a degree of abrasion resistance in a cylinder block, by constituting this cylinder block with an aluminum alloy containing a specified quantity of silicon, while fitting a plastic ring in a ring groove of a piston. CO...
|
|
JPS6140949Y2 |
|
|
JPS61261681A |
PURPOSE: To smoothly reset a wobble plate from a small tilt angle to a large tilt angle, by retractably providing a stopper, which restricts the wobble plate to a minimum swivel angle, through the urging action of a spring. CONSTITUTION:...
|
|
JPS61256153A |
An air conditioning unit for cooling and dehumidifying a passenger room of a vehicle including a reciprocatory piston type refrigerant compressor having a refrigerant suction chamber, a compressed refrigerant discharge chamber, and an in...
|
|
JPS61255285A |
PURPOSE: To smooth the swing of a waffle plate by providing a crank chamber and an admission chamber communicating to each other through a bypass escapement hole in addition to a fixed escapement hole to restrain pressure rise in the cra...
|
|
JPS61173872U |
|
|
JPS61237891A |
PURPOSE: To sufficiently hold lubricating oil in a crank chamber by allowing the inlet of a pressure adjusting valve in a crank chamber to communicate to the lower part of a high-pressure chamber, in a swing plate type compressor which c...
|
|
JPS61237887A |
PURPOSE: To vary the capacity of the swash plate type fluid machinery by forming a small hole for discharging the working fluid in a cylinder in the course of compression to the low pressure side onto the cylinder head onto which the edg...
|
|
JPS6147986B2 |
|
|
JPS6147985B2 |
A shoe for use in a swash-plate type compressor and made of a base material of steel, is slidably disposed between the swash-plate and a steel ball rotatably supported in a recess of a piston and is provided on one side thereof with a li...
|
|
JPS6146710B2 |
A modulation delay valve for a variable capacity compressor operative to prevent the premature reduction of the pumping capacity of the compressor. A compressor suction chamber pressure sensing bellows, located in a pressure control cell...
|
|
JPS61162583U |
|
|
JPS61162582U |
|
|
JPS6143555B2 |
|
|
JPS61215469A |
PURPOSE: To increase the amount of oil in the reduction gas to the crank chamber thus to improve the lubrication performance by coupling between the suction chamber for varying the inclination angle of an inclination board for varying th...
|
|
JPS61215812A |
PURPOSE:To facilitate the assemblage of a pump and provide the compact pump by interconnecting a pair of connecting plates of both opposed inside edge ends of a pair of arcuate holders and connecting plates of the other holders opposed t...
|
|
JPS6132154Y2 |
|
|
JPS6132155Y2 |
|
|
JPS61147380U |
|
|
JPS6131195Y2 |
|
|
JPS61145885U |
|
|
JPS61145887U |
A two-stage air compressor unit having an intercooler and aftercooler placed in side by side relationship to form an integral unit which is cooled by forced air blown by a motor driven fan and which has the inlet and outlet parts located...
|
|
JPS61145884U |
In a compressor with a mechanism for reducing pulsating pressure variations, with a large number of pistons (3) which carry out reciprocating movements in cylinder bores (2), a coincidence of pulsating variations of the suction pressure ...
|
|
JPS61145883U |
In a compressor with a mechanism for reducing pulsating pressure variations, with a cylinder block (1) with a large number of cylinder bores (2), with a large number of pistons (3) which are inserted in the cylinder bores (2) and carry o...
|
