| Document |
Document Title |
|
JPH05638B2 |
|
|
JPH04359794A |
PURPOSE: To make it possible to use an air flow which is discharged outdoors and clean a dust removing filter with its air flow by mounting integrally said dust removing filter with an end face of a rotary element which is open to an out...
|
|
JPH0478915B2 |
|
|
JPH04129665U |
|
|
JPH0450437Y2 |
|
|
JPH0450438Y2 |
|
|
JPH0474639B2 |
|
|
JPH0474638B2 |
|
|
JPH0449499Y2 |
|
|
JPH0449498Y2 |
|
|
JPH04295597A |
PURPOSE: To prevent the generation of cracks or the like due to pins in a rotary heat accumulating type ceramic heat exchanging body provided with a plurality of pins employed for rotating and provided on the outer peripheral part. CONST...
|
|
JPH0459560B2 |
|
|
JPH0459559B2 |
|
|
JPH0459558B2 |
|
|
JPH04108159U |
|
|
JPH04240393A |
PURPOSE: To secure the cooling property of a seal member sufficiently in a rotary heat accumulating type heat exchanger. CONSTITUTION: A rotating center area 11, not faced to high-temperature gas flow passages 3, 4, is provided in a heat...
|
|
JPH04236094A |
PURPOSE: To make a soot blower unnecessary and prevent the title device from corrosion due to exhaust gas by a method wherein a basket, made of a synthetic resin and a metal, is filled with heat transfer elements, made of the synthetic r...
|
|
JPH0492161U |
|
|
JPH0492160U |
|
|
JPH0429246Y2 |
|
|
JPH0473756U |
|
|
JPH0438995B2 |
An element basket assembly (30) for a rotary regenerative heat exchanger (2) comprised of a plurality of heat transfer element plates (32) stacked in an array between first and second end plates (34,36) disposed at opposite ends of the s...
|
|
JPH0424314Y2 |
|
|
JPH0465115U |
|
|
JPH0434079B2 |
|
|
JPH0434075B2 |
|
|
JPH0457068U |
|
|
JPH0419342Y2 |
|
|
JPH0423181B2 |
PURPOSE:To contrive to improve the heat transmission performance by a structure wherein a second heat exchanger is provided in a second heat exchange tank located below a liquid receiver tank. CONSTITUTION:A second heat exchanger 16 is p...
|
|
JPH0441977U |
|
|
JPH0493592A |
PURPOSE: To prevent hot gas from directly jetting against a wall surface of a housing by a method wherein a guide member for changing the direction of flow of hot gas flowing from a branch pipe is installed inside the housing of hot gas....
|
|
JPH0415006B2 |
|
|
JPH0411794B2 |
|
|
JPH0460388A |
PURPOSE: To enhance heat exchanging performance and to reduce a manufacturing cost by reducing heights of blades at an inner periphery, provided radially from a rotating center at front and rear sides in a disc state lower than those at ...
|
|
JPH045902Y2 |
A regenerative air preheater has a heat-exchange sector plate centered on an axis and formed with a multiplicity of axially throughgoing passages with intake and output heating-gas hoods axially flanking the plate and conduits for passin...
|
|
JPH0410269U |
|
|
JPH0410266U |
|
|
JPH044516B2 |
|
|
JPH0420790A |
PURPOSE: To ensure a satisfactory sealing property at all times by reducing the amount of thermal deformation of each inner housing due to a temperature difference by constructing an inner housing assembly by facing a semi-cylinder type ...
|
|
JPH046393A |
PURPOSE: To seal a circumferential gap between a rotor and a rotor housing effectively by a method wherein a circumferential seal mechanism is constituted of a seal block assembly having seal elements made of ceramics and seal plates con...
|
|
JPH043890A |
PURPOSE: To miniaturize the above device, reduce the cost of the same and improve reliability by a constitution wherein a housing assembly is retained in a casing elastically with a predetermined gap while two sets of heat accumulating c...
|
|
JPH03286993A |
PURPOSE: To enhance temp. efficiency by realizing a counter flow type heat exchanger in spite of a heat accumulation type by mounting a large number of discs or annular discs on one shaft or cylinder so as to pierce the same in a comb sh...
|
|
JPH0366597B2 |
PURPOSE:To contrive to enhance efficiency of total heat exchange, by a method wherein a rotor provided with moisture-permeable moisture-absorptive partition plates stacked in a circumferential direction with a spacing therebetween is rot...
|
|
JPH0366593B2 |
PURPOSE:To improve heat exchanging efficiency and reduce sliding sounds by a method wherein a rotor is formed by laminating a plurality of layers of partitioning plates having heat transfer properties and humidity permeating properties i...
|
|
JPH0366596B2 |
PURPOSE:To contrive to separately perform sensible heat exchange and total heat exchange at high efficiency in a single heat exchanger, by a method wherein a columnar rotor provided with moisture-nonpermeable moisture-absorptive partitio...
|
|
JPH0366594B2 |
PURPOSE:To increase heat exchanging efficiency and reduce sliding sounds by a method wherein a plurality of partitioning plates, having a non-permeating property for moisture but having moisture absorbing property, are laminated into cir...
|
|
JPH0366595B2 |
PURPOSE:To reduce the sliding sound of a rotor by a method wherein the rotor is rotated and a primary air current and a secondary air current change their flowing positions for each other periodically so that the heat storage capacity of...
|
|
JPH0366598B2 |
PURPOSE:To enhance heat-exchanging efficiency, by a method wherein exchange of heat in a regenerative transmission rotary type heat exchanger for effectively exchanging heat between a primary gas flow and a secondary gas flow is effected...
|
|
JPH0396578U |
|
|
JPH0360040B2 |
A method and an apparatus for the manufacture of heat-exchanger rolls (10). The roll (10) consists of two webs (12, 14) of material which are wound together in superposed relationship. One (12) of the webs is corrugated and formed with p...
|
