| Document |
Document Title |
|
JPH05314906A |
PURPOSE: To eliminate the irregularity and lowering of brightness and also prevent the imperfection of airtightness by placing a sinter body of glass in annular form on the circumferential edge of the projection part of a lid member havi...
|
|
JPH0545005Y2 |
|
|
JPH0580098B2 |
An efficiently cooled display tube is obtained by pumping a low viscosity liquid having a high heat capacity through a cooling space less than 1 mm. thick on the outside of the display window. A chamber is smoothly connected to the inlet...
|
|
JPH0578135B2 |
|
|
JPH05275000A |
PURPOSE: To enhance the critical current value of superconductors by passing opposite currents through adjacent superconductors and to extend the distance between terminals so as to increase the resistance coefficient of heat conduction ...
|
|
JPH0576131B2 |
There is provided a metallic tape supporting a mercury vapour releasing material, preferably Ti3Hg, admixed with a non-evaporable getter metal, preferably an alloy of 84% Zr - 16% Al, contained within a continuous series of depressions w...
|
|
JPH0541492Y2 |
|
|
JPH05258661A |
PURPOSE: To facilitate the assembling of a yoke in a waveguide circuit. CONSTITUTION: A magnet 8 and a spacer 11 are nipped by a yoke 1 and a yoke 2 from both sides of a chassis 9 and a chassis 10, and the yoke 2 is mounted on a support ...
|
|
JPH05254588A |
PURPOSE: To provide a protective vessel for non-evaporation type getter materials that is simple, easy to open and easily usable. CONSTITUTION: This provides the first sheet 102 composed of a thermally stable material and the second shee...
|
|
JPH0538514Y2 |
|
|
JPH05249295A |
PURPOSE: To obtain a radioactive ray emitting panel of the structure capable of uniformly illuminating in a large area, increasing the visible area of a display without increasing the size of a display casing without protruding from the ...
|
|
JPH0568053B2 |
|
|
JPH05242832A |
PURPOSE: To simplify replacement of a getter by a construction wherein an inner surface of a cap is pushed by a getter with its one end held on an opening in an end portion in the direction of a neck of a magnetic screening cap, and the ...
|
|
JPH05208324A |
PURPOSE: To manufacture a probe of which the radius of curvature of the extreme end is small and the aspect ratio is small with good reproducibility by executing work for improving wettability of etching liquid on the circumferential par...
|
|
JPH05205854A |
PURPOSE: To provide an evenly distributed composition by putting a predetermined amount of carbon black in crystalline polyethylene having specific MFR, and preventing destruction of the carbon black during kneading. CONSTITUTION: Polyet...
|
|
JPH05505337A |
(57) [Summary] Since this publication is application data before electronic filing, summary data is not recorded.
|
|
JPH0546151B2 |
|
|
JPH05159697A |
PURPOSE: To provide a high density Ti-W non-evaporating type getter excellent in gas absorbing performance which can be manufactured without using a binder. CONSTITUTION: A Ti-W non-evaporating type getter is made of a pressurized molded...
|
|
JPH0517784Y2 |
|
|
JPH0531253B2 |
|
|
JPH0517785Y2 |
|
|
JPH0583661A |
PURPOSE: To provide a projector which is free from the change of the focal distance due to the rise of temperature of a CRT by setting a positive lens right before a negative lens consisting of a cooling liquid and a shell lens. CONSTITU...
|
|
JPH054193Y2 |
|
|
JPH052987A |
PURPOSE: To suppress the costs for manufacturing a getter through perfect selection of the front and rear surfaces and to enhance the flashing effect by furnishing a flange protrusive at the end of the opening of a getter vessel; and eli...
|
|
JPH0481295B2 |
A hydrocarbon getter pump for use in sealed envelopes comprises an active metal alloy capable of gettering hydrogen, a nickel catalyst and means for heating the nickel catalyst and getter material from 300 DEG to 500 DEG centigrade. The ...
|
|
JPH0452928Y2 |
|
|
JPH0451411Y2 |
|
|
JPH0451410Y2 |
|
|
JPH0449806Y2 |
|
|
JPH0449810Y2 |
|
|
JPH0448624Y2 |
|
|
JPH0446367Y2 |
|
|
JPH0464130B2 |
|
|
JPH0499341U |
|
|
JPH0496960U |
|
|
JPH04233125A |
PURPOSE: To provide a getter strip structure with increased getter capacity by increasing the filling amount of getter powder per unit surface area. CONSTITUTION: A getter strip structure contains pressed getter powder in and on an open ...
|
|
JPH04229923A |
PURPOSE: To provide a structure and its manufacturing method by which materials emitted from a structure as a gas to an active electronic area of an electric field electron radiator can be easily removed. CONSTITUTION: A conductive base ...
|
|
JPH0487137U |
|
|
JPH04190544A |
PURPOSE: To obtain a large deposition area and realize a getter device which has such a capacity as a larger vacuum pump has by providing a bridging means which bridge a wire getter and a net deposition plate on the deposition face of a ...
|
|
JPH0425798Y2 |
|
|
JPH04171637A |
PURPOSE: To keep the internal liquid pressure constant with high reliability at a low cost by connecting a long tube opened to the outside air at one tip section to one portion of a liquid container formed in a space between a face and a...
|
|
JPH0424593Y2 |
|
|
JPH0422533Y2 |
|
|
JPH04133250A |
PURPOSE: To prevent any damage on a cathode ray tube by providing the first getter metal vapor releasing material capable of releasing barium vapor when heating and the second getter metal vapor releasing material capable of releasing ti...
|
|
JPH0425660B2 |
|
|
JPH0416480Y2 |
|
|
JPH04101334A |
PURPOSE: To simplify a construction while dispensing with cooling liquid, to thereby reduce a manufacturing cost by forming the front of a CRT in a lens shape, and providing a cooling means thereat. CONSTITUTION: A front panel side 510 o...
|
|
JPH04101335A |
PURPOSE: To improve heat radiation and prevent heating of receiver apparatus by using a transparent film bag which is filled with cooling liquid while has a space partly without cooling liquid, wherein the liquid part are connected to th...
|
|
JPH0419662B2 |
A getter assembly is described which has an antenna mount in the form of a small bar placed along the diameter of an annular container. The antenna mount is formed in such a way as to touch the container only in areas near to the inner w...
|
|
JPH0411326Y2 |
|
